Filter
Top Products
88
Controlling the AR-3000R from an External Device
4.
When the prompt appears on the screen, press the
ENTER button to enable the settings.
To quit without making the settings, use the SELECT dial to
choose “NO,” then press the ENTER button.
Once the settings have been made successfully, you’re
returned to the setting item selection screen.
5.
Press the MODE button.
This ends the setting process and returns you to the usual
screen.
* If you press the MODE button while making settings, a
message asking you to confirm that you want to exit the
setting process appears. Note that if you choose “YES,” then
press the ENTER button, you are returned to the usual screen,
and all setting changes you’ve made up to that point will be
discarded.
Selecting the Direct Playback Method
Select the Direct Playback Method (NORMAL/FIRST-IN/
LAST-IN/ SEQUENCE) to be used.
“Operational Specifications for Direct Playback”
→
p. 86
Procedure for Setting the Direct Playback
Method
1.
Press the MODE button.
The MODE indicator lights up.
2.
Use the SELECT dial to choose “5.2 Direct Play,” then
press the dial.
3.
Turn the SELECT dial to choose the Direct Playback
system (NORMAL, FIRST-IN, LAST-IN, or SEQUENCE),
then press the dial.
fig.14-g02e
• If making the settings in “Assigning Phrases to the
Ports,” proceed to Step 4 in the procedure for assigning
the phrases.
• To quit making settings, press the ENTER button.
4.
When the prompt appears on the screen, press the
ENTER button to enable the settings.
To quit without making the settings, use the SELECT dial to
choose “NO,” then press the ENTER button.
Once the settings have been made successfully, you’re
returned to the setting item selection screen.
5.
Press the MODE button.
This ends the setting process and returns you to the usual
screen.
* If you press the MODE button while making settings, a
message asking you to confirm that you want to exit the
setting process appears. Note that if you choose YES, then
press the ENTER button, you are returned to the usual screen,
and all setting changes you’ve made up to that point will be
discarded.
Assigning Phrases to the Ports
Assign phrases to control input Port Nos. 1 through 16.
If not assigning a phrase to a port, select “-----.”
While you can select phrases from Card A as well as Card B,
note that playback will not work properly if the card inserted
when the phrase was registered is not inserted at the time of
playback (if the phrase is not saved, the playback signal is
disregarded).
Settings When Formatting Cards (in Slot A)
fig.14-14e
Port No.
Phrase
...
...
1
A0001
2
A0002
3
A0003 A0004
4
A0005
516
A0016
By assigning “PLAY” instead of a phrase, you can obtain
the same functions from that port as you do using the
PLAY button on the front panel.
<During Direct Playback>
By inputting a control signal to the port to which
“PLAY” is assigned, you can play back the phrase
indicated in the display. This is convenient when you
want to use an external device to start playback of
phrases selected with the SELECT dial.
You can also stop playback using the STOP port.
<While in Phrase Record Standby>
When recording phrases, you can use the control input
terminals to start and stop recording (for more on
recording methods, please read “Recording Audio” (p.
40) as well).
When in recording standby, if the port to which “PLAY”
is assigned is set to “ON,” recording will begin. This is
convenient when you want to start recording remotely,
using an external device.
You can also stop recording using the Stop port.
* However, this method cannot be used for switching to
recording standby, even when control signals are sent to
both the port to which “PLAY” is assigned and the STOP
port.
AR-3000R_e.book 88 ページ ２０１０年３月１８日 木曜日 午後２時６分