Filter
Top Products
120
Playing Two Units’s Worth of Data on
the Left and Right (Dual Mono Mode)
What Is the Dual Mono Mode?/
Equipment Connections
The Dual Mono mode is a feature for playing different mono
audio phrases independently on the left and right channels.
By playing odd-numbered phrases (A0001, A0003,... or
B0001, B0003,...) from the left channel and even-numbered
phrases (A0002, A0004,... or B0002, B0004,...) from the right
channel, you can play back two units’s worth of data on a
single unit.
You can also play back separate phrases on the left and right
channels either simultaneously, or shifted.
fig.18-01e (What Is the Mono Mode?)
Note that the Dual Mono mode is subject to various
conditions that you should be aware of before you use the
mode.
On the AR-2000/100 (legacy models), this Dual Mono mode
is named the “Channel Playback mode.” As you use it, keep
in mind that it is the same feature.
Conditions for Simultaneous Playback in Dual
Mono Mode
●
Phrases Whose Recording Type Is Mono
●
RDAC-Grade and RDAC-Mode Must Be Uniform
Specifying Phrases Like the Following Result in
Dual Mono Mode Playback That May Not Be
Correct
●
MIDI Phrases, Song Phrases
→
These are treated as empty phrases.
●
Pattern Phrases Containing MIDI Phrases
→
These are treated as empty phrases, and the unit searches
for and plays back the next phrase.
●
Phrases Whose Recording Type Is Stereo
→
Dual Mono playback is canceled, and the specified phrase
is output in stereo (L/R).
●
Phrases for Which RDAC-Grade and RDAC-Mode Are
Different
→
The phrase already being played back is stopped, and the
next specified phrase is played.
If a phrase unsuited to Dual Mono playback is specified on
either the left or right channel in the course of sequential
phrase playback, it results in incorrect Dual Mono playback.
To ensure reliable Dual Mono playback, specify the playback
phrases with care.
Dual Mono playback can be made possible by converting
stereo phrases to mono phrases. You can also make Dual
Mono playback possible for phrases having different RDAC-
modes by converting them after recording to make them
uniform. For more about how to convert phrases, refer to
“Phrase Convert” (p. 78).
The following phrase information has no
effect during playback.
●
1.5 Loop Play
Control Output During Dual Mono Mode
Playback
During Dual Mono mode playback, the left-channel Busy
Out signal is output from the BUSY OUT control port, and
the right-channel Busy Out signal is output from the CONT
OUT control port.
* Note that no Control Out signal is output (because the
Control Out setting (p. 59) is not valid).
AR-3000R Settings
Set the Dual Mono Mode to “ON (MONO 2ch).”
Procedure for Setting the Dual Mono Mode
1.
Press the MODE button.
The MODE indicator lights up.
2.
Use the SELECT dial to choose “9.1 Dual Mono Mode,”
then press the dial.
3.
Turn the SELECT dial to choose Dual Mono Mode (ON
(MONO 2ch)), then press the dial.
fig.18-g01e
4.
When the prompt appears on the screen, press the
ENTER button to enable the settings.
To quit without making the settings, use the SELECT dial to
choose “NO,” then press the ENTER button.
When you’re finished making the setting, the display returns
to the setting item selection screen.
5.
Press the MODE button.
This ends the setting process and returns you to the usual
screen.
LR
Odd-numbered
phrases
A0001
A0003
B0001
....
Even-numbered
phrases
A0002
A0004
B0002
....
AR-3000R_e.book 120ページ ２０１０年３月１８日 木曜日 午後２時６分