Filter
Top Products
122
Playing Two Units's Worth of Data on the Left and Right
●
Last-In Playback
• Because port Nos. 1 and 3 are allocated to output L,
depending on the port priority, playback of A0001 is
halted and A0003 is played back.
• Because port No. 2 is allocated to output R, A0002
continues to be played back even during playback of
A0003 or A0001.
●
Sequence Playback
• The control signals for port Nos. 3 and 4 are stored in
memory (reserved), and after playback of A0001 and
A0002 ends, A0003 and A0004 are played.
• Because A0005 is a stereo phrase, playback of A0004 is
stopped, and the specified phrase is played back in
stereo (left and right).
During Program Playback
Odd-numbered phrases are output by program playback
from output L (left), and even-numbered phrases are output
by program playback from output R (right).
* Because Start signals are ignored during playback of one
phrase, simultaneous playback of output L and R is not
possible.
When you send a Stop input signal, playback stops
simultaneously for the L and R channels.
During Binary Playback
Odd-numbered phrases are output by binary playback from
output L (left), and even-numbered phrases are output by
binary playback from output R (right).
When you send a Stop input signal, playback stops
simultaneously for the L and R channels.
●
When Level is set to “ON” and Edge is set to “OFF”
• Any new Start signal input during A0002 playback is not
valid.
• Playback is repeated while binary is specified for A0003
and the Start signal is continuously input.
●
When Level is set to “OFF” and Edge is set to “ON”
• A0001 is played back only once.
• A0002 is played back only once, then ends, even when
binary is specified for A0002 and the Start signal is
continuously input.
Dual Mono Playback Through MIDI
Signals
You can perform playback through MIDI signals, in the same
way as for ordinary stereo playback. Playback starts when a
MIDI Note On message is received. Odd-numbered phrases
are played back from the L (left) channel, and even-
numbered phrases are played back from the R (right)
channel.
* Because playback is performed in reverse priority, the last-
receive Note On message takes priority.
* Setting Note Trigger to “Gate” makes it possible to send stop
instructions independently to the left and right channels.
Dual Mono Playback Through the RS-
232C Connector
In a manner similar to ordinary stereo playback, you can also
obtain playback through the RS-232C connector. Phrase
playback-sequence information is allocated to the
corresponding dedicated buffer according to whether the
phrase number is odd or even, and playback on the left and
right channels starts simultaneously according to the
respective playback sequence.
* Sending a playback-stop instruction stops playback
simultaneously on the left and right channels.
Port 1
Output R
Port 2
Port 3
Output L
A0002
A0001 A0003
A0001 Interrupted
Port 3
Output R
Port 4
Port 5
Output L
A0001
A0002
A0003
A0004
Port 2
Port 1
A0004 Interrupted
A0005
A0005
A0005
: Stereo phrase
Output R
Output L
A0001
A0002
START port
A0003
Output R
Output L
A0001
Binary Signal
Port 1-11
START port
A0001
A0002
A0002
Ignored
A0003
A0003 A0003
Output R
Output L
A0001
A0002
Binary Signal
Port 1-11
START port
A0001 A0002
Ignored
AR-3000R_e.book 122ページ ２０１０年３月１８日 木曜日 午後２時６分