Filter
Top Products
129
Appendices
Troubleshooting
About recording
Can’t record a connected device
Has the selection of the recording connector (LINE-IN,
LINE+MIC-IN, DIGITAL-IN, or MIDI-IN) been made
correctly?
Make sure the device connected to the connector matches the
selected recording connector.
→
“Selecting the Recording Connector” (p. 43)
Recording does not start
Is the trigger recording setting set to LOW, MID, or HIGH?
In trigger recording, recording starts automatically when the
audio input is of a higher level than the trigger level (lever
for starting recording).
If you are not conducting trigger recording, set it to “OFF.”
→
“Trigger Recording Setting” (p. 48)
About playback
Phrases are not played back correctly
Has the card been formatted on a computer?
Be sure to format cards on an AR series device.
Phrases are not played back (PAUSE indicator
lit in orange).
Is the MTC “Sync Source” set to “MTC?”
When not synchronizing playback with MTC and using the
AR-3000R as a slave, set “Sync Source” on the AR-3000R to
“INTERNAL.”
Pattern phrases and song phrases are not
played back as intended
When creating a pattern phrase or song phrase, you can
choose actual phrases with constituents from both card A
and card B. At the time of playback, however, if the card
containing the constituent phrases is not inserted, playback
will not occur in the normal fashion. (If a constituent phrase
is not present, the unit seeks and plays back the next phrase.)
Make sure the phrases assigned during creation exist on the
cards.
→
“Pattern phrase” (p. 62)
→
“Song phrase” (p. 65)
The start of phrase playback is delayed when
playback is controlled from an external device
Has the “Delay Time” been set for the phrase?
Try playing back the phrase by pressing the AR-3000R’s
PLAY button (manual operation). If the start of playback is
delayed, check the AR-3000R to confirm whether or not the
delay time has been set.
→
“Delay Time” (p. 55)
If the playback is correct when you press the AR-3000R’s
PLAY button, check the control signals being sent from the
external control device, connections and so on once more.
Control Input Playback (Direct/Program/
Binary) does not work as intended
Select the correct type of control input (Direct, Program, or Binary).
You cannot achieve control input playback merely by connecting a
device to the port. Be sure to set the control input mode and match
the method used for connecting to the connectors.
Phrases in Direct Playback cannot be selected
as intended
Phrases are assigned to Ports 1 to 16 by means of settings
made on the AR-3000R.
When a card is formatted, the assignments are Port No. 1–
phrase A0001, Port No. 2–phrase A0002,..., Port No. 16–
phrase A0016.
→
“Assigning Phrases to the Ports” (p. 88)
Phrases in Direct Playback do not stop
playing.
Check the phrase settings and make sure that “Repeat Play”
is not set to “ON.”
→
“Repeat Play” (p. 57)
In Program Playback, phrases cannot be
selected as intended.
The assignments of phrases in the Program Playback
sequence are made with settings on the unit.
When a card is formatted, the assignments are No. 1–phrase
A0001, No. 2–phrase A0002,..., No. 100–phrase A0100.
→
“Registering Phrases” (p. 92)
Dual Mono playback does not work as
intended.
In the system settings, is “Dual Mono Mode” set to “OFF
(STEREO 1ch)?”
When you are using Dual Mono mode, be sure to set this to
“ON (MONO 2ch).”
Also, Dual Mono mode playback is subject to a wide variety
of conditions.
Check these carefully when using. For detailed information
about the conditions, refer to “What Is Dual Mono Mode?”
(p. 120).
AR-3000R_e.book 129ページ ２０１０年３月１８日 木曜日 午後２時６分