Filter
Top Products
Figures
1. Port side of the SAN384B (sample
configuration) ............3
2. Port side of the SAN384B with the exhaust kit
installed (sample configuration) ......4
3. Blower (non-port) side of the SAN384B . . . 4
4. Assembled lift tool with 24-inch load plate 16
5. Lift tool positioned next to the chassis on the
shipping tray ............17
6. Port-side exhaust kit assembly for 27 to 31 in.
(68.58 to 78.74 cm) cabinets .......19
7. Clip and retainer nut locations on exhaust side
cabinet rails (example showing relative
positions) .............21
8. Shelf installed in cabinet ........22
9. Air duct installed into side slot in shelf 22
10. Installing the top rail assembly to the duct
assembly and cabinet rails .......23
11. Lift tool and chassis positioned at rear of
cabinet ..............24
12. Load plate extended inside the cabinet to the
exhaust kit shelf ...........25
13. Chassis half way into cabinet on load plate 26
14. Location of screws to attach the chassis to the
cabinet rails ............27
15. Attaching the vertical cable management
finger assemblies to the cabinet rails ....28
16. Cable design for the mSFP patch cables for the
FC8-64 high density port blade ......30
17. Flow of configuration tasks for the SAN384B 34
18. FC8-16 port blade ..........46
19. FC8-32 port blade ..........46
20. FC8-48 port blade ..........47
21. FC8-64 port blade ..........47
22. FC10-6 port blade ..........48
23. FR4-18i routing blade .........49
24. FX8-24 extension blade.........49
25. FCOE10-24 blade...........49
26. Control processor blade (CP8) LEDs ....54
27. Core switch blade (CR4S-8) .......55
28. Power supply ............57
29. Blower assembly LEDs.........58
30. WWN bezel ............59
31. Chassis door ............62
32. Cable management finger assemblies ....63
33. Port blade removal and installation (48-port
blade shown as example) ........65
34. Filler panel removal and installation ....67
35. Removing the control processor (CP8) blade 70
36. Removing and replacing the core switch blade 74
37. Location of the two power supplies ....75
38. Removing and installing a power supply 76
39. Blower assembly removal and replacement 78
40. WWN bezel and card removal and installation 80
41. Optical transceiver (SFP, SFP+, and XFP)
extraction tool............82
42. Replacing an optical transceiver......82
43. Optical mSFP transceiver ........83
44. ICL cable .............85
45. ICL cable connections between two SAN384B
chassis ..............87
46. ICL cable connections between a SAN384B
chassis and a SAN768B chassis. ......88
47. 3-way ICL cable connections between a
SAN384B chassis and two SAN768B chassis. . 89
48. 3-way ICL cable connections between a
SAN768B chassis and two SAN384B chassis. . 90
49. 3-way ICL cable connections between three
SAN384B chassis. ..........91
50. Battery locations on the SAN384B.....106
51. FC8-16 port blade ..........137
52. FC8-32 port blade ..........137
53. FC8-48 port blade ..........138
54. FC8-64 port blade ..........138
55. FC10-6 port blade, ports 0-5 from right to left 138
56. FR4-18i routing blade .........138
57. FX8-24 extension blade ........139
58. FCOE10-24 blade ..........139
© Copyright IBM Corp. 2009, 2010 ix
|
||
||
||
|
||
||
||
|
||
||
||
||
||
||
||
||
||