Filter
Top Products
TASCAM HS-4000 45
7 – Timeline mode
Playback in timeline mode
Project/session selection
1. Press the PROJECT key on the front panel to open the
PROJECT screen.
2. Touch the e button next to the project that you want
to play to open the session selection screen. If it is not
the current project, a pop-up window appears
confirming that you want to load it. Touch the
OK
button.
3. Touch a session name button to select that session.
4. Touch the
MENU button to open a pull-up menu and
touch the
LOAD button.
The “
Load selected Session?” pop-up appears.
5. Touch the OK button.
When loading completes, the Home Screen opens.
Setting input monitoring
Turn input monitoring OFF for the channels (tracks) that you are
playing back. If input monitoring is ON for a channel, sound will
be input through the corresponding input connector.
1. Touch the
REC/MON button on the Home Screen to
open a pull-up with REC and MON buttons.
2. If input monitoring is on for any playback channels
(MON buttons appear blue), touch those MON
buttons to turn them off (turning them gray).
Setting the online function
Refer to “Online functions” on page 89 and make settings for the
nline outputs. o
Locate to the playback start position
Use the m [ ] and , [ ] keys, jump to a mark or
use the manual locate function to locate to the time where you
want to start playback
When time code synchronization is ON, playback will occur at
the input time code, so locating as described above is not
necessary.
Playback control in timeline mode
Press the PLAY key to start playback.
Press the PAUSE key to pause playback.
Press the PLAY key again to resume playback.
P
ress the STOP (RETAKE) key to stop playback.
Press the . [MARK.] key or / [MARK/] key to skip
to the start of another region.
Press and hold the m [
] or , [ ] key to search
backward or forward.
Press the . [MARK.] or / [MARK/] key while
pressing and holding the SHIFT key to move between marks.
Press and hold the m [
] or , [ ] key while
pressing and holding the SHIFT key to search at high-speed.
While pressing the STOP key, press the . [MARK .] key or/
[MARK/] key to skip to the beginning of the first region
recorded or the end of the last region. (This only works with
the front panel keys.)
NOTE
Playback functions can also be used through parallel control.
Using the call function
Press the CALL (CHASE) key to locate to the point where
playback was last started from playback standby (call point) and
put the unit in playback standby mode.
BWF–J cue point
When the Follow BWF–J item is set to ON, if a BWF–J cue point is
detected during playback, the following corresponding
operation will occur. In addition, if the BWF–J Tally Out item is set
to ON, in response to each BWF–J cue point, the CUE signal and
tally signal will be output from the parallel remote connector.
However, when playback is synchronized with time code, only
he CUE signal and tally signal will be output. t
BC$STANDBY When a session is loaded, the transport
locates to the first BC$STANDBY point that
occurs and pauses. During playback,
playback pauses when this point is
reached. In either case, a BC$STANDBY tally
is output.
BC$CM During playback, when this point is
reached, a BC$CM CUE signal is output.
BC$END During playback, when this point is
reached, a BC$END CUE signal is output.
BC$STOP During playback, when this point is
reached, a BC$STOP CUE signal is output,
and playback stops.
BC$FILE During playback, when this point is
reached, a BC$END CUE signal is output. If
the beginning of a following entry
(BC$STANDBY CUE point) exists, that CUE
will be followed.
BC$PAUSE During playback, when this point is
reached, a BC$PAUSE tally is output, and
playback pauses.