Filter
Top Products
150
For Long and Trouble-Free Operation: Specifications
Reference input: Automatic switching of black burst/HD 3
value SYNC, BNC × 1 (loop through × 1),
automatic 75 Ω termination provided
SDI input: BNC × 1, complies with SMPTE 292M/
296M/299M during HD SDI input, complies
with SMPTE 259M-C/272M-A, ITU-R BT.656-
4 during SD SDI input
VIDEO OUTPUT
Analog component (switchable):
BNC × 3 (Y, P
B, PR)
Y: 1.0 V[p-p], 75 Ω during HD output mode
Analog composite output (switchable):
BNC × 3, video 1, video 2, video 3,
1.0 V[p-p], 75 Ω during SD output mode
HD SDI/SD SDI output (switchable):
BNC×1, complies with SMPTE 292M/296M/
299M during HD serial digital output, complies
with SMPTE 259M-C/272M-A, ITU-R BT.656-4
during SD serial digital output
Monitor output: BNC × 1, 1.0 V[p-p], 75 Ω
DIGITAL AUDIO
Sampling frequencies:
48 kHz (synchronous with video)
Quantizing: 16 bits
Frequency response:
20 Hz to 20 kHz ±1.0 dB
(at the reference level)
Dynamic range: Better than 85 dB
(1 kHz emphasis off, “A” weighted)
Distortion: Less than 0.1 %
(1 kHz, emphasis off, reference level)
Crosstalk: Less than –80 dB
(1 kHz, between 2 channels)
Headroom: 18/20 dB selectable
De-emphasis: T1 = 50 µs, T2 = 15 µs (auto on/off)
AUDIO INPUT
Analog input (CH1, CH2, CH3, CH4):
XLR × 4, 600 Ω/high impedance selectable
(factory setting: high impedance)
+4/0/–3/–20 dBu selectable
Only CH2 input can be switched between
LINE/MIC/MIC +48 V
MIC: –60 dBu
MIC+48V: Phantom +48V supported, –60 dBu
SDI input: BNC × 1, complies with SMPTE 292M/296M/
299M during HD SDI input, complies with
SMPTE 259M-C/272M-A (480/59.94i), ITU-R
BT.656-4 (576/50i) during SD SDI input
AUDIO OUTPUT
Analog output (CH1, CH2, CH3, CH4):
XLR × 4, low impedance,
+4/0/–3/–20 dBu selectable
SDI output: BNC × 1, complies with SMPTE 292M/296M/
299M during HD SDI input, complies with
SMPTE 259M-C/272M-A (480/59.94i), ITU-R
BT.656-4 (576/50i) during SD SDI input
Monitor output: Pin jacks × 2, –8 dBV, 600 Ω
Headphones: Stereo mini jack (3.5 mm diameter), 8 Ω,
variable level
Time code input: BNC × 1, 0.5 V[p-p] to 8.0 V[p-p], 10 kΩ
Time code output: BNC × 1, 2.0 V[p-p] ±0.5 V[p-p],
low impedance
RS-422A input/output:
D-sub 9pin, RS-422A interface
IEEE1394 input/output:
IEEE1394 6pin × 1
400/200/100 Mbps selectable
Complies with IEEE1394-1995
Complies with IEC61883-Part1,Part2
AV/C Command Set supported
USB 2.0: Host × 1, Device × 1
AUDIO
Other input/output
Inrush current, measured according to European standard
EN55103-1: 20.5 A
Mass and dimensions are approximate values.
Specifications are subject to change without notice.