79
PRV-LX1
En
Symptom
Main unit command buttons
don’t work.
Can’t output 96 kHz audio in
digital.
Remote control unit doesn’t
work.
Television malfunctions.
Memory settings are erased.
No sound from speakers, or
distorted sound.
When digital video camera is
connected to the unit’s DV
connectors, video images can’t
be viewed on television monitor.
Or no sound is audible.
DVD playback images can’t be
seen on the monitor screen of a
digital video camera connected
to the unit’s DV connectors. Or
no sound is audible.
Cause/Remedy
¶ Hold the STANDBY/ON button depressed for 4 seconds or more
to set unit to standby condition. If the STANDBY/ON button also
doesn’t work, turn off the main power switch on the rear panel.
¶ Some discs prohibit digital output of 96 kHz linear PCM audio. In
this case, even if the unit’s [96 kHz PCM OUT] command is set
to “96 kHz”, the signal will be converted to 48 kHz for output.
¶ Operate remote within proper range (7 m).
¶ Change to new batteries.
¶ Television monitors with wireless remote control functions may
malfunction when the PRV-LX1’s remote control unit is used. In
such cases, separate the television monitor and the PRV-LX1.
¶ If manual disconnection of the power cord or a power failure
occurs when the unit is turned on, previously input settings may
be erased. Disconnect the power cord only after pressing the
STANDBY/ON button so that the display’s POWER-OFF
indicator goes out.
¶ If television or AV amplifier’s sound volume is set to minimum,
raise the sound volume.
¶ When using audio input from external input connector, set the
[Audio Level] command.
¶ Check and confirm that all audio cables are connected properly.
¶ Check that all cable plugs are inserted securely in their
connectors or jacks.
¶ Clean any dirt from connection plugs and jacks.
¶ No sound is produced during still, frame advance, and slow playback.
¶ DTS audio is output only from unit’s digital audio output
connectors. To listen to DTS audio from a DVD disc, the unit’s
digital audio output connectors must be connected to the digital
audio input connectors of a DTS compliant amplifier, and the
[DTS OUT] command must be set to “ON”. If the connected
amplifier does not support DTS audio, use the remote control
unit’s AUDIO button or the disc menu to select an audio format
other than DTS.
¶ Check all connections. The PRV-LX1’s DV connectors allow the
connection of a single digital video camera. Connect the digital
video camera directly to the PRV-LX1.
¶ Check that the DV cable is connected properly.
¶ Try turning the power to the digital video camera OFF then ON again.
¶ Turn the power to the PRV-LX1 OFF then ON again.
¶ Check all connections. The PRV-LX1’s DV connectors allow the
connection of a single digital video camera. Connect the digital
video camera directly to the PRV-LX1.
¶ Check that the DV cable is connected properly.
¶ Try stopping playback and then starting it again.
¶ Try turning the power to the digital video camera OFF then ON again.
¶ Turn the power to the PRV-LX1 OFF then ON again.
¶ The video and audio of DVDs labeled “copying prohibited” or
“copy once only” cannot be output.
¶ The audio/video of a component connected to an external input
connector cannot be output.
¶ No video or audio signals are output during recording or during
recording pause.
¶ When using time shift playback (playback during recording), even
if recording alone is stopped, output of playback video/audio will
not begin. Stop playback temporarily, then start it once again to
begin signal output.
¶ Set [DV OUT] to “Enabled”.
Reference page
47
17
17
6
34
46
48
Malfunctions may be caused by static electricity or other external sources. In such cases, normal operation may be restored
by disconnecting the power cord and then reconnecting it again. If problem persist, consult your dealer.
TROUBLESHOOTING