JVC BR-DV6000U MP3 Player User Manual


  Open as PDF
of 61
 
E-59
:Setting:
Ⅵ Set TCG SOURCE to “INTERNAL”.
Ⅵ Set TCG SELECT to “PRESET”.
Ⅵ TCG MODE:
REC-RUN : The time code runs only during recording.
FREE-RUN : The time code runs from the point when the preset
is completed.
❈
In the case of the user
’s bit, setting is not required.
...TC/UB/CLOCK(1/2) Menu screen
BR-DV6000
PROFESSIONAL
MENU RESET
A.DUB
EJECT
COUNTER
AUDIO INPUT
SELECT
MONITOR OUTPUT REMOTE
LOCAL
CTL L
MIX
R
CH-1/2
MIX
CH-3/4
DV
LINE
Y/C
(CPN)
TC
UB
REW STOP FF
REC
OPERATE
PLAY PAUSE
DISP
SET INDEX+
BLANK CUE UP
HOLD
PHONES REC LEVEL
CH-1/3 CH-2/4
MIC
INDEX–
Mini
KCABEGAP
EGAPTXEN
FFOTESFFOCT
FFOETACILPUDCT
NO)LAP(TIBFD
–––)CSTN(FD/FDN
NUR-CEREDOMGCT
TESERPTCELESGCT
LANRETNIECRUOSGCT
––)–2/1(KCOLC/BU/CT–––
CH1/3
00
H
00
M
00
S
00
F
RRUN
CH2/4
STOP
SP222
min
01/02/03
01:23:45
AM
OVER
48k
T
C
L
dB010203040
OVER
Y/C
SYNC
r
e
CF
Variable values can be set for the time code and the user
’s bit for efficient material management
and editing.
Memo
● To stop the setting, press
the HOLD button to return
to the normal screen.
● To preset all digits to 0,
press the RESET button
when any of the digits is
blinking.
● When the hour digit is blink-
ing, the frame digit starts
blinking when the ; button
is pressed.
● If a user’s bit is input with
its all digits set as
“F”, BR-DV6000 converts
FFFFFFFF to FFFFFFFE
before recording.
:Operation:
This section descr
ibes the setting of the time code. The setting of
the user’s bit is the same. Values that can be used to configure
the user’s bit are hexadecimal numeral from 0
– F.
1.
Set the counter switch to TC.
(For user’s bit, set the switch to UB.)
2.
Press the DISP button to change the LCD to its enlarged dis-
play mode.
3.
In the STOP mode, press the HOLD button.
¥ The hour digit of the counter starts blinking.
4.
Press the 8 or 9 button to change the value.
5.
Press the : or ; button to move blinking to the next digit.
6.
Press the 8 or 9 button to change the value of the blinking
digit.
7.
Repeat steps
5
and
6
to perform the necessary settings.
8.
Press the SET button to confirm the setting value and blink-
ing of the counter stops.
... Perform setting while checking the LCD display.
TIME CODE
– Presetting the time code –
SET
button
DISP/8 button
9 button : buttonHOLD button
LCD display
RESET button
COUNTER
switch
; button
TC/UB/CLOCK(1/2) Menu screen
59
:Setting:
Ⅵ Set TCG SOURCE to “INTERNAL”.
Ⅵ Set TCG SELECT to “PRESET”.
Ⅵ TCG MODE:
REC-RUN : The time code runs only during recording.
FREE-RUN : The time code runs from the point when the preset
is completed.
❈
In the case of the user
’s bit, setting is not required.
Ⅵ NDF/DF (NTSC):
NON DROP : Non-drop frame mode. Use this setting if the number
of frame is more important.
DROP : Drop frame mode. Use this setting if the recording
time is more important.
...TC/UB/CLOCK(1/2) Menu screen
BR-DV6000
PROFESSIONAL
MENU RESET
A.DUB
EJECT
COUNTER
AUDIO INPUT
SELECT
MONITOR OUTPUT REMOTE
LOCAL
CTL L
MIX
R
CH-1/2
MIX
CH-3/4
DV
LINE
Y/C
(CPN)
TC
UB
REW STOP FF
REC
OPERATE
PLAY PAUSE
DISP
SET INDEX+
BLANK CUE UP
HOLD
PHONES REC LEVEL
CH-1/3 CH-2/4
MIC
INDEX–
Mini
KCABEGAP
EGAPTXEN
FFOTESFFOCT
FFOETACILPUDCT
–––)LAP(TIBFD
PORD)CSTN(FD/FDN
NUR-CEREDOMGCT
TESERPTCELESGCT
LANRETNIECRUOSGCT
––)–2/1(KCOLC/BU/CT–––
CH1/3
NDF
00
H
00
M
00
S
00
F
RRUN
CH2/4
STOP
SP222
min
01/02/03
01:23:45
AM
OVER
48k
T
C
L
dB010203040
OVER
Y/C
SYNC
r
e
CF
Variable values can be set for the time code and the user
’s bit for efficient material management
and editing.
Memo
● To stop the setting, press
the HOLD button to return
to the normal screen.
● To preset all digits to 0,
press the RESET button
when any of the digits is
blinking.
● When the hour digit is blink-
ing, the frame digit starts
blinking when the ; button
is pressed.
● If a user’s bit is input with
its all digits set as
“F”, BR-DV6000 converts
FFFFFFFF to FFFFFFFE
before recording.
:Operation:
This section describes the setting of the time code. The setting of
the user’s bit is the same. Values that can be used to configure
the user’s bit are hexadecimal numeral from 0
– F.
1.
Set the counter switch to TC.
(For user’s bit, set the switch to UB.)
2.
Press the DISP button to change the LCD to its enlarged dis-
play mode.
3.
In the STOP mode, press the HOLD button.
¥ The hour digit of the counter starts blinking.
4.
Press the 8 or 9 button to change the value.
5.
Press the : or ; button to move blinking to the next digit.
6.
Press the 8 or 9 button to change the value of the blinking
digit.
7.
Repeat steps
5
and
6
to perform the necessary settings.
8.
Press the SET button to confirm the setting value and blink-
ing of the counter stops.
... Perform setting while checking the LCD display.
TIME CODE
– Presetting the time code –
SET
button
DISP/8 button
9 button : button
TC/UB/CLOCK[1/2] Menu screen
LCD display
RESET button
COUNTER
switch
; button
E
U
 previous next