Filter
Top Products
23
32K CH–1/2 0SP mi n00
BLANK SEARCH
INDEX DETECTED
03/04/03 STANDBY
-
OFF
11:20:00 TCR 02:00:00:00
A
B
ON-SCREEN DISPLAY
– Status/Event display –
4
5
6
VCR operation mode
Remaining tape
Edit mode display
Displays the VCR operation mode, including:
PLAY, EJECT, FF, REW, STANDBY-ON, STANDBY-OFF, STILL,
REC, REC PAUSE, A. DUB, A. DUB PAUSE, ASSEM EDIT, INSERT
EDIT, SHTL (shuttle search), JOG, BLANK SRH (blank search),
NO CASSETTE (cassette tape not loaded), OPERATE OFF.
For SHTL and JOG, the speed is also displayed.
• The display can be turned on/off with VCR MODE in the DISPLAY
Menu screen.
Displays the remaining time of tape (minutes).
While the remaining time is being confirmed, “ – ––” is displayed.
• The display can be turned on/off with TAPE REMAIN in the DIS-
PLAY Menu screen.
• The SP display disappears when a DVCAM cassette tape is be-
ing played back.
• This remaining tape time display is only for reference.
Displays the edit mode selected, e.g., by using the edit mode controller.
• ASSEM :Assemble editing
• INS V :Video insert editing
• INS A :Audio insert editing (Audio: both CH 1 and CH 2)
• INS VA :Video, audio insert editing (Audio: both CH 1 and
CH 2)
• INS VA :Video/Audio insert editing
• INS TC :Time code insert editing (Time code only)
Inser
t editing in the 32 k audio mode
• INS A12 :CH1, CH2 audio
• INS A34 :CH3, CH4 audio
• INS VA12:Video & CH1, CH2 audio
• INS VA34:Video & CH3, CH4 audio
• INS A :CH1 to CH4 audio
• INS VA :Video & CH1 to CH4 audio
The display can be turned on/off with EDIT INFO in the DISPLAY
Menu screen.
Memo
If the counter display po-
sition is set to the upper
right, this item will be dis-
played on the lower right.
No. Item Description
Memo
● With the counter dis-
play shown on the top
left, this display ap-
pears on the bottom
right.
● In the 48 k audio mode,
insert editing is not
possible in the follow-
ing cases.
INS A1, INS A2, INS
VA1, INS VA2
● “B” display: displayed for about 3 seconds
Display Description
INDEX
DETECTED
VIDEO END
DETECTED
An index has been detected
during index repeat operation.
The video end has been de-
tected during end repeat op-
eration.
● “A” display: displayed during operation
Display Description
BLANK
SEARCH
INDEX +1
INDEX MARK
Blank search in progress.
Index search in progress.
The number indicates the index
search position.
When an index has been speci-
fied on the tape during record-
ing.
Ⅵ Event display : When certain functions are in use, it is displayed at the following posi-
tions (with the DISPLAY mode ON or AUTO).
22
32K CH–1/2 0SP mi n00
ASSEM
W
ARNING 7001
DRUM MOTOR FAI LURE
REC I NH IB IT
03/04/03 STANDBY
-
OFF
11:20:00 TCR 02:00:00:00
ON-SCREEN DISPLAY
– Status display – (continued)
No. Item Description
3
Counter display Displays the CTR counter, time code or user’s bit. The dis-
played contents can be selected using the COUNTER switch.
• CTL counter: It will be displayed if the COUNTER switch is
set to CTL. The counter shows a 7-digit
number (hour, minute, second and frame) with
+ or – and “CTL” at the beginning, e.g., CTL-
9:30:20:10
• Time code : It will be displayed if the COUNTER switch is
set to TC. The time code shows an 8-digit
number (hour, minute, second and frame)
At playback, the time codes recorded on the
tape are displayed.
The prefix indicates the time code mode.
TCG : Time code generator data
TCR : Time code reader data
DTCG : Time code data received from the DV IN / OUT
terminal
ETCG : External time code generator data
Depending on the framing mode, the symbols for the sec-
onds and frames are different (only for NTSC).
00 : 00 : 00 : 00
Dot (.) for the drop frame mode
¥ Colon (:) for the non-drop frame mode
• User’s bit : it will be displayed if the COUNTER switch is
set to UB.
The user’s bit is an 8-digit number (each digit
is a number or character from 0 – F).
The prefix indicates the user’s bit mode.
UBG : User’s bit generator data
UBR : User’s bit reader data
DUBG : User’s bit reader data received from the DV IN /
OUT terminal
EUBG : External user’s bit generator data
Memo
●
The position of the counter display can be changed with
COUNTER POSI in the DISPLAY Menu screen.
●
The counter display can be turned on/off with TIME
CODE in the DISPLAY Menu screen.