Filter
Top Products
84
RQT8346
Messages
On the unit’s display
The following messages or service numbers appear on the unit’s display when something unusual is detected during startup and use.
¢ The messages are alternately displayed.
HARD ERR
¢
≥If there is no change after turning the unit on and off, consult the dealer where the unit was
purchased.
—
No AUDIO
¢
≥Should you connect equipment that does not support CPPM the audio from the CPPM copy
protected DVD-Audio cannot be output from HDMI AV OUT terminal. Connect the audio
cable of the Audio/Video cable (Red, White) to a HDMI compatible AUDIO IN terminal.
—
No READ ≥The disc is dirty or badly scratched. The unit cannot record, play, or edit.
≥You have used a DVD lens cleaner and it has finished. Press [<, OPEN/CLOSE] on the
main unit to eject the disc.
11
11
PLEASE WAIT
¢
≥Displayed when the unit is started. This is not a malfunction.
≥The unit is carrying out its recovery process. You cannot operate the unit while “PLEASE
WAIT” is displayed.
—
—
SET ∑
(“∑” stands for a number.)
≥The remote control and main unit are using different codes. Change the code on the remote
control.
Press and hold [ENTER] and the indicated number button at the
same time for more than 2 seconds.
26
SLEEP ≥In order to extend HDD life, the HDD is in SLEEP mode. 10
SP 15:50
EP 120 h
“SP”, “EP” and the numbers are
examples.
≥Available space on the HDD or disc.
The example “SP 15:50” is displayed when less than 100 hours are available and the
example “EP 120h” is displayed when over 100 hours are available.
“SP” and “EP” are recording modes, “15:50” means “15 hours 50 minutes” and “120h”
means “120 hours”.
29
UNFORMAT
¢
≥You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL or
DVD-RW (DVD-Video format) that has been recorded on other equipment.
Format the disc to use it.
However all the recorded contents on a disc are deleted.
—
UNSUPPORT
¢
≥You have inserted a disc the unit cannot play or record on. 5–7
F74 ≥The HDMI connection could not be authenticated due to a transfer malfunction. —
F75 ≥The HDMI connection could not be authenticated due to an internal data malfunction. —
U59 ≥The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes until the
message disappears.
Select a position with good ventilation when installing the unit. Do not block the cooling fan
on the rear of the unit.
—
U61 ≥(When a disc is not inserted) Displays when a malfunction has occurred during recording,
playback or copy. This is displayed when the unit is in the recovery process to return to
normal operation; it is not broken. Once the display clears you can use the unit again.
—
U71 ≥The connected equipment is not HDMI compatible. —
U72
U73
≥The HDMI connection acts unusually.
- The connected equipment is not HDMI compatible.
- The HDMI cable is too long. Please use a cable 5.0 meters or less.
- The HDMI cable is damaged.
—
U88 ≥(When a disc is inserted) Displays when there was something unusual detected with the
disc while playback or copy. This is displayed when the unit is in the recovery process to
return to normal operation; it is not broken. Once the display clears you can use the unit
again.
85
U99 ≥The unit fails to operate properly. Press [POWER Í/I] on the main unit to switch the unit to
standby. Now press [POWER Í/I] on the main unit again to turn the unit on.
—
H∑∑ or F∑∑
(“∑” stands for a number.)
≥There is something unusual. (The service number displayed after “H” or “F” depends on the
unit’s condition.)
≥Check the unit using the troubleshooting guide. If the service number does not disappear,
do the following.
[1] Disconnect the plug from the AC outlet, wait a few seconds, then reconnect it.
[2] Press [POWER Í/I] to turn the power on. (The unit may be fixed.)
If the service number does not disappear despite doing the above, request service from
the dealer. Inform the dealer of the service number when requesting service.
—
85–91
M6740P.book 84 ページ ２００６年１月３０日 月曜日 午後３時３０分