Filter
Top Products
79
RQT8346
Channel/Clock settings when TV Guide On Screen
®
system is not used
Refer to the control reference on page 74.
Preparation:
If the program listings has already been downloaded, return the unit to the factory preset condition using the steps indicated below.
When the unit is on and stopped
1 Press and hold [CH, X] and [CH, W] on the main unit for about 5 seconds.
The unit turns off.
2 Press [Í, DVD/VHS POWER] to turn the unit on.
3 After the language and TV aspect is setup, press [RETURN] and exit the TV Guide
On Screen
®
system setup screen.
Note
You can set scheduled recording only manually after you set the unit with “Set Channels
Automatically”.
[1] While stopped
Press [FUNCTIONS].
[2] Press [3, 4] to select “Other Functions” and
then press [ENTER].
[3] Press [3, 4] to select “Setup” and then press
[ENTER].
[4] Press [3, 4] to select “Channel” and then
press [1].
[5] Press [3, 4] to select “Set Channels
Automatically” and then press [ENTER].
[6] Press [ENTER].
Auto Channel Setting starts. This takes a few minutes.
The unit then proceeds with Auto Clock Setting. The time is
displayed when finished.
≥DST, Daylight Saving Time, shows the summertime setting.
≥TIME ZONE shows the time difference from Greenwich Mean
Time (GMT).
EST (Eastern Standard Time) l GMT j5
CST (Central Standard Time) l GMT j6
MST (Mountain Standard Time) l GMT j7
PST (Pacific Standard Time) l GMT j8
AST (Alaska Standard Time) l GMT j9
HST (Hawaii Standard Time) l GMT j10
For other areas: xx hr
≥If the Auto Clock Setting does not start automatically, select
“Clock Settings” from the “Setup” tab and then select “Set
Clock Automatically”.
≥If the time was not set correctly, use manual clock setting
(l 25) or adjust time zone.
[7] Press [ENTER].
≥Regarding DST (Daylight Saving Time) l 25
≥The unit configures channels according to the Signal Source
(RF IN) settings as follows.
Adjust the time zone (j1 or i1) if it was not set correctly with auto
clock setting.
You cannot change this setting if you set the clock manually.
[1] While stopped
Press [FUNCTIONS].
[2] Press [3, 4] to select “Other Functions” and
then press [ENTER].
[3] Press [3, 4] to select “Setup” and then press
[ENTER].
[4] Press [3, 4] to select “Setup” and then press
[1].
[5] Press [3, 4] to select “Clock Settings” and
then press [ENTER].
[6] Press [3, 4] to select “Adjust Time Zone” and
then press [ENTER].
≥Regarding DST (Daylight Saving Time) l 25
[7] Press [3, 4] to select “s1” or “r1” and then
press [ENTER].
To return to the previous screen
Press [RETURN].
To exit the screen
Press [RETURN] several times.
To cancel partway while Auto Channel/Clock Setting is taking place
Press [RETURN].
To set so the TV Guide On Screen
®
system is not displayed automatically when you turn the unit on
When the power is turned on and the Start setup screen is displayed, press [3, 4] to select “Don’t remind me again” and press [ENTER].
Auto channel/clock settings
Setup
Disc
Channel
Video
Audio
Display
Set Clock Automatically
Auto Clock Setting is complete.
11/4/2006 12:15 AM
DST.............. On
Time Zone..... CST
Setup
Signal Source
(RF IN)
Band Channel
Antenna
VHF 2 to 13
UHF 14 to 69
CableTV
VHF 2 to 13
CATV LOW BAND 95 to 99
CATV MID/SUPER BAND 14 to 36
CATV HYPER BAND 37 to 65
ULTRA BAND
66 to 94
100 to 125
SPECIAL CATV CHANNEL 1
∫ Adjust Time Zone
Setup
Setup
Audio
Adjust Time Zone
j1
0
i1
Channel
Disc
Video
Changing the unit’s settings/Channel/Clock settings when TV Guide On Screen
®
system is not used
M6740P.book 79 ページ ２００６年１月３０日 月曜日 午後３時３０分