Filter
Top Products
Reference
70
VQT0P03
VHSDVD
Operation Page
Picture Page
Cannot operate the TV. ≥Change manufacturer code. Some TVs cannot be operated even if you change the code.
≥Press [AV] to change the input mode to “TV”.
17
24, 51
Cannot operate the DVD. ≥Press [DVD] when operating DVD. 11
Cannot operate the VHS. ≥Press [VHS] when operating VHS. 11
The remote control doesn’t
work.
≥The remote control and main unit are using different codes. Change the code on the remote
control.
Press and hold [ENTER] and the indicated number
button at the same time for more than 2 seconds.
≥The batteries are depleted. Replace them with new ones.
≥Point the remote control at the remote control sensor on the main unit.
≥Remove obstacles between the remote control and main unit.
≥Don’t place the signal sensor in direct sunlight or in areas that may be subject to sunlight
exposure.
≥The child lock function is activated.
17
12
12
–
–
46
The unit is on but cannot be
operated.
≥Some operations are prohibited by the disc.
≥The unit is warm (“U59” appears on the unit’s display). Wait until “U59” disappears.
≥One of the unit’s safety devices may have been activated.
Reset the unit as follows:
(1) Press [Í/I] on the main unit to switch to standby.
If the unit doesn’t switch to standby, press and hold [Í/I] on the main unit for about 10
seconds. The unit is forcibly switched to standby.
Alternatively, disconnect the AC mains lead, wait for about 1 minute, then reconnect it.
(2) Press [Í/I] on the main unit to turn the unit on.
≥The child lock function is activated.
–
68
–
46
Cannot eject a disc. ≥The unit is recording.
≥The unit may have a problem. While the unit is off, hold down [∫] and [CH, W] on the DVD
main unit simultaneously for about 5 seconds. Remove the disc and consult the dealer.
≥The child lock function is activated.
–
–
46
Cannot tune channels. ≥Check the connections. 14
Startup is slow. ≥Make sure that “Quick Start” is set to “On”.
Even if “Quick Start” is set to “On”, startup is slow if the clock is not set, there was a power
failure or the AC plug has just been connected.
≥A few dozen seconds after turning on the unit, you can play a disc or start recording to discs
other than DVD-RAM.
≥Startup takes time for a few minutes after 5:15 a.m. due to system maintenance of this unit.
43
–
–
Takes time to read DVD-RAM. ≥It may take time to read a disc if it is being used for the first time in this unit or it has not been
used for a long time.
–
TV reception worsens after
connecting the unit.
≥This can occur because the signals are being divided between the unit and other equipment. It
can be solved by using a signal booster, available from audio-visual suppliers.
–
The images from the unit do not
appear on the TV.
Picture is distorted.
≥Make sure that the TV is connected to the VIDEO OUT terminal, S VIDEO OUT terminal or
COMPONENT VIDEO OUT terminals on the unit.
≥Make sure that the TV’s input setting (e.g., AV 1) is correct.
≥The TV isn’t compatible with progressive signals. Press and hold [∫] and [“ DVD, DUBBING]
on the DVD main unit at the same time for about 5 seconds. The setting will change to
interlace.
14, 15
–
–
The TV screen is distorted when
switching the DVD/VHS.
≥The colour of the screen may turn to monochrome or the screen may be distorted depending
on the TV used when you switch the DVD/VHS. However, this is not a malfunction.
–
M7620(GN).book 70 ページ ２００５年５月２５日 水曜日 午後１２時２分