Filter
Top Products
Reference
68
VQT0P03
VHSDVD
On the unit’s display Page
On the TV Page
On the unit’s display Page
Error messages
∫ Common
H, F
(“” stands for a
number.)
≥An error has occurred. The number following “H” or “F” depends on the status of the unit.
Reset procedure: (“The unit is on but cannot be operated.” l 70)
≥If the service numbers fail to clear, note the service numbers and contact a qualified service person.
–
–
X HOLD ≥The Child Lock function is activated.
Press and hold [ENTER] and [RETURN] simultaneously until “X HOLD” disappears.
46
∫ DVD
Cannot finish recording
completely.
≥The programme was copy-protected.
≥The disc may be full.
≥There are already 99 recorded titles ([+R] 49 recorded titles).
–
–
–
Cannot playback.
TV system is different from
the setting.
To playback, please change
the TV System in SETUP.
≥You tried to play a title recorded using a different encoding system from that of the TV system
currently selected on the unit.
Alter the “TV System” setting on this unit to suit.
42
Cannot record on the disc. ≥The disc may be dirty or scratched. 9
Unable to format.
Please check the disc.
Cannot record. Disc is full. ≥Create space by erasing any unnecessary titles. [RAM] [-RW‹V›]
[Even if you erase recorded content from the DVD-R or +R, there is no increase in disc space. Available
disc space on DVD-RW (DVD-Video format) increases only when the last recorded title is erased.]
≥Use a new disc.
20, 28,
31
–
Cannot record. Maximum
number of titles exceeded.
Error has occurred. Please
press ENTER.
≥Press [ENTER] to start recovery process. You cannot operate the unit while it is recovering
(“SLF CHECK” appears on the unit’s display).
–
No Disc ≥The disc is upside down. 8
Please change the disc. ≥There may be a problem with the disc. Press [<, OPEN/CLOSE] on the main unit to remove it and
check it for scratches or dirt. (The unit turns off automatically after you open the tray.)
9
This is a non-recordable
disc.
≥The unit cannot record on the disc you inserted. Insert a DVD-RAM or unfinalized DVD-R, DVD-
RW (DVD-Video format) or +R.
≥You inserted an unformatted DVD-RAM or DVD-RW. Format the disc with the unit.
–
29
This disc is not formatted
properly.
≥The operation is prohibited by the unit or disc. –
HARD ERR ≥If there is no change after turning the unit on and off, consult the dealer where the unit was purchased. –
NO READ ≥The disc is dirty or badly scratched. The unit cannot record, play, or edit.
≥You have used a lens cleaner and it has finished. Press [<, OPEN/CLOSE] on the main unit to eject the
disc.
9
9
PROG FULL ≥There are already 16 timer programmes. Delete unnecessary timer programmes. 27, 53
REMOTE MODE ∑
(“∑” stands for a
number.)
≥The remote control and main unit are using different codes. Change the code on the remote control.
Press and hold [ENTER] and the indicated number button at the
same time for more than 2 seconds.
17
SLF CHECK ≥There was a power failure or the AC plug was disconnected while the unit was on. The unit is carrying out its
recovery process. Wait until the message disappears.
≥If “Quick Start” is set to “On”, “PLEASE WAIT” is displayed while the unit is carrying out its recovery process.
You cannot operate the unit while this is displayed.
–
–
UNFORMAT ≥You have inserted a DVD-RAM or a DVD-RW that is unformatted or a DVD-RW recorded on other
equipment.
29
UNSUPPORT ≥You have inserted a disc the unit cannot play or record on. 6, 7
U59 ≥The unit is very warm.
The unit switches to standby for safety reasons. Wait for about 30 minutes until the message disappears.
Select a position with good ventilation when installing the unit. Do not block the cooling fan on the rear of the
unit.
–
U99 ≥The unit fails to operate properly. Press [Í/I] on the main unit to switch the unit to standby. Now press [Í/I]
on the main unit again to turn the unit on.
–
M7620(GN).book 68 ページ ２００５年５月２５日 水曜日 午後１２時２分