Filter
Top Products
67
CONDENSATION
ON DRUM
WARNING 3200
LOADING FAILURE
WARNING 3300
LOADING FAILURE
WARNING 4100
CASSETTE
EJECT FAILURE
DEFECTIVE
TAPE!
5605 - 5609
WARNING 5702
TAPE END DET.
ERROR!
WARNING 5802
TAPE BEGIN
DET. ERROR!
WARNING 7001
DRUM MOTOR
FAILURE
WARNING 7101
CAP MOTOR
FAILURE
WARNING7202 -
7203
SUPPLY REEL
FAILURE
WARNING7302 -
7303
TAKE UP REEL
FAILURE
WARNING7305
TAKE UP REEL
FAILURE
WARNING 7401
REEL MOTOR
FAILURE
Condensation
Unable to load tape
Unable to eject tape
Eject error
Tape is cut
Tape ending sensor error
Tape begin sensor error
Drum rotation error
Capstan rotation error
Supply reel rotation error
Take up reel rotation error.
Tape winding error during unloading
Reel motor rotation error
Please leave the power on and wait for
the display to disappear.
This error can be resolved by restarting
the unit. However, doing so may dam-
age the tape in some cases. Please
consult your JVC authorized dealer.
Press the EJECT button and retrieve the
cassette.
Then replace the tape.
This error can be resolved by restarting
the unit. However, doing so may dam-
age the tape in some cases. Please
consult your JVC authorized dealer.
Ⅵ Warning display (Displayed regardless of the DISPLAY mode)
When a warning display appears, this unit stops operation and cease to accept any opera-
tion commands. When TAPE DEFFECTIVE (5605 - 5609) is displayed, the unit similarly
stops operation but accepts one command, viz EJECT.
Display Status Action
Memo
This unit uses a microcomputer. It may not function correctly if there is external noise. If this happens,
please turn off the power and then on again.
→
For servicing
Refer to the servicemanual page. 1-10 “1.8.7 Error history menu”
66
OTHERS
–
Warning display
–
When an anomaly occurs, this unit automatically identifies the cause and displays an error-
coded warning message on the monitor.
If the unit is in a state needing rectification, or if an operation error has occurred, an alarm
display will be shown on the monitor.
32K CH–1/2
SP
000
min
W
ARNING 7001
DRUM MOTOR FAI LURE
04/01/02 STANDBY
-
OFF
11:20:00 TCR 02:00:00:00
Warning display
32K CH–1/2
SP
000
min
HEAD CLEANING REQUIRED!
04/01/02 STANDBY
-
OFF
11:20:00 TCR 02:00:00:00
Alarm display
Ⅵ Alarm display (Displayed regardless of the DISPLAY mode)
Display Status Action
LOW VOLTAGE
HEAD CLEANING
REQUIRED!
OVER HEATING!
The DC power voltage is low.
The unit will eventually go into the OPERATE
OFF mode if operation is continued.
The video head is dirty. If the head is clogged, it
will be detected and the alarm message will be
displayed during the PLAYBACK mode. When
the STOP mode is engaged or when the cas-
sette is ejected, the display will go off.
When the head clog is cleared, the message
will disappear.
The internal temperature of the unit has ex-
ceeded the regulated value.
Please check the power voltage.
Please clean it with the dedi-
cated head-cleaning tape.
(
☞
Page 8)
If the message persists despite
cleaning, it could be due to bad
recording condition, bad tape or
lifespan of the head.
Please disconnect the power
and place the unit in a cool
place. If this message is dis-
played again, the unit may have
been damaged. Please consult
your JVC authorized dealer.
• For alarm displays resulting from operation errors, please refer to page 22.