Filter
Top Products
48
PLAYBACK
–
Repeat playback
–
This unit is capable of 3 types of repeat playback.
The repeat playback function is set via the REPEAT MODE item of the SYSTEM (1/2) menu.
TAPE END
VIDEO END
Playback
INDEX
Rewind
Index signal
Beginning of tape End of tape
Index signal
–––SYSTEM[1/2]–––
STL/F.ADV 2ND
BACKUP REC TIME OFF
LONG PAUSE TIME 5MIN
LONG PAUSE MODE F.ADV
INDEX
W
RITE ON
REPEAT MODE BLANK
NEXT PAGE
PAGE BACK
SYSTEM (1/2) menu
Setting
ⅥREPEAT MODE item of the SYSTEM (1/2) menu
OFF :No repeat playback
INDEX :Repeat playback between positions where index sig-
nals are recorded.
VIDEO END :Repeat playback from the beginning of the tape to
the position where video signal recording ends.
TAPE END :Repeat playback from the beginning to the end of
the tape.
Operation
1.
Press the REW button and rewind the tape to the be-
ginning.
2.
Press the PLAY button to begin replay.
¥ When it reaches the position set at the REPEAT MODE menu
item, the tape rewinds and plays back again.
ⅥTo abort the repeat playback function, press the STOP
button.
Repeat operation
INDEX repeat playback
• If no index signal is de-
tected during playback, the
tape will run till the end. If
no index signal is detected
during rewind, the tape will
rewind till the beginning.
• If the interval between in-
dex signals is less than 1
minute, the function may
not work well.
Memo
If there is dust adhered to the
head, repeat playback may
not work well.
49
PLAYBACK
–
Selecting playback audio output
–
The output mode for audio playback can be selected with the remote controller.
DISPLAY
BARS
MENU SEARCH+
SEARCH–
A.DUB
F.REV
INDEX– INDEX+
PLAY
STOP
REMOTE CONTROL UNIT
RM-G3000
REW FF
PAUSE
SET
BLANK
STILL
MODE
AUDIO
MUTING
OUT SEL.
OUT LEV.
REC
F.ADV
AUDIO MUTING
button
OUT SEL
button
OUT LEV
button
Memo
• The output channel for playback audio of tapes
recorded in the 32kHz mode can also be set
via the AUDIO OUT SEL item of the AUDIO/
VIDEO menu of the main unit.
• The audio output level can be set via the AU-
DIO OUT LEVEL item of the AUDIO/VIDEO
menu.
☞
Page 61 “AUDIO/VIDEO menu”
Ⅵ To turn the audio muting function ON/
OFF or to mute the EE audio, press the
AUDIO MUTING button.
To resume the audio output, press the button
again.
Ⅵ Selecting the audio output channel for
playback of tapes recorded in the 32kHz
mode.
Each time the OUT SEL. button is pressed, the
channel changes in the following sequence:
• CH3/CH4: CH3 audio is output via the CH1/3
AUDIO OUT terminal whereas CH4 audio is
output via the CH2/4 AUDIO OUT terminal.
• MIX: Sounds mixed from CH1 and CH3 are
output via the CH1/3 AUDIO OUT terminal
whereas Sounds mixed from CH2 and CH4 are
output via the CH2/4 AUDIO OUT terminal.
CH1/CH2 CH3/CH4 MIX
Note
Depending on the sound source, noise may oc-
cur in the MIX mode. In this case, please use
CH1/CH2 or CH3/CH4.
Ⅵ Select the output level for audio play-
back
Each time the OUT LEV button is pressed, the
standard level for the output audio level changes.
(NORMAL or ATT)
•To play back tapes recorded at a standard level
of –12dB (using a consumer DV device), set
the output level to ATT. In so doing, the audio
output level decreases.
•To play back tapes recorded on this unit, set
the output level to NORMAL.