Filter
Top Products
39
RECORDING
–
Audio dubbing
–
For tapes recorded in the 32kHz audio mode, audio dubbing can be performed on the CH3 and
CH4 channel after the recording. (After-recording)
Notes
• For tapes recorded in the 48kHz audio mode, audio dubbing cannot be performed.
• Audio dubbing cannot be performed for DV input signals.
A.DUB
F.REV
INDEX– INDEX+
PLAY
STOP
REMOTE CONTROL UNIT
RM-G3000
REW FF
PAU SE
REC
F.A DV
1. 4.
PLAY
button
2. 3.
PAUSE button
5.
STOP
button
3.
A.DUB
button
Mini
PROFESSIONAL
SET
MENIU
EJECT
REC PLAY
PAU SE
REW
STOP
FF
DVCAM NTSC
PAL
REC INH.
CH-1/3
CH-2/4
BR-DV3000
A.DUB
OPERATE
INPUT SEL.REMOTE SEL.
MIC
SERIAL
WIRELESS
9PIN
LINE
DV
Y/C
2. 3.
PAUSE
button
5.
STOP buttonINPUT SEL switch
1. 4.
PLAY button
3.
A.DUB button
MIC
terminal
Connection
Audio dubbing sounds are input from the AUDIO IN
terminal on the rear panel or the MIC terminal on
the front panel. MIC terminal prevail over the AU-
DIO IN terminal.
Setting
• Set the AUDIO item of the AUDIO/VIDEO menu
to 32k.
• Do not set the INPUT SEL switch on the front
panel to DV.
Operation
1.
Press the PLAY button to play the tape.
2.
At the position where you want to au-
dio dub, press the PAUSE button.
¥ The unit goes into the STILL mode.
3.
Hold down the PAUSE button and press
the A.DUB button.
¥ The unit goes into the audio dubbing pause
mode.
4.
Press the PLAY button.
¥ Audio dubbing begins. Audio signals are
recorded on the CH3 and CH4 channel.
Ⅵ To stop audio dubbing temporarily, press
the PAUSE button.
5.
To end audio dubbing, press the STOP
button.
Memo
• During audio dubbing, if the tape comes to a
part recorded in a non dubbing-feasible mode
(such as LP mode or 48kHz audio mode), the
VTR will enter the STOP mode. When this hap-
pens, high-volume noise from the DV output
will occur. Hence, before audio-dubbing, please
check the recording mode of the tape.
• In the case that a microphone is connected to
the MIC terminal, sound output from this ter-
minal will be recorded. In the absence of MIC
input, signals from the CH1/3, CH2/4 AUDIO
IN terminal on the rear panel will be recorded.
• When audio dubbing cannot be performed, an
alarm message will be displayed on the moni-
tor. (
☞
Page 23)
• Audio dubbing PAUSE cannot be executed di-
rectly in the STOP mode. Please execute it in
the STILL mode.
During audio dubbing pause, sound from the
CH3/CH4 channel is output via the monitor but
sound output from the DV terminal is not pos-
sible.
• If audio dubbing is repeated on a short section
of the tape, noise may occur for an instant when
the section is played.
• During audio dubbing, noise may be produced
on the playback video or EE sound but the re-
cording is normal.
• The playback sound of CH1/2 cannot be re-
corded on CH3/4 (sound on sound).
• During backspace operation of audio dubbing,
audio dubbing cannot be performed on unre-
corded parts.
• When audio dubbing is performed on tapes re-
corded on other devices, it may not record cor-
rectly. Please record with this unit before per-
forming audio dubbing.
38
RECORDING
–
Recording method
–
Main unit
Remote controller
Mini
PROFESSIONAL
SET
MENIU
EJECT
REC PLAY
PAUSE
REW
STOP
FF
DVCAM NTSC
PAL
REC INH.
CH-1/3
CH-2/4
BR-DV3000
A.DUB
OPERATE
INPUT SEL.REMOTE SEL.
MIC
SERIAL
WIRELESS
9PIN
LINE
DV
Y/C
3.
PAUSE
button
5.
STOP button
2. 4.
PLAY
button
2.
REC
button
A.DUB
F.REV
INDEX– INDEX+
PLAY
STOP
REMOTE CONTROL UNIT
RM-G3000
REW FF
PAUSE
REC
F.A DV
2. 4.
PLAY
button
2.
REC button
5.
STOP
button
3.
PAUSE button
Memo
• If recording has been
paused for an extended pe-
riod of time, the unit will au-
tomatically go into the
STOP mode to protect the
tape. The time period after
the lapse of which the unit
will enter the STOP mode
can be configured via the
LONG PAUSE TIME item of
the SYSTEM (1/2) menu.
• This unit cannot perform
editing functions.
1.
Load the cassette.
• Before loading the cassette, please check that the rear slide of
the cassette is pushed to REC.
¥ The Main unit is powered on.
2.
Start recording.
• Hold down the REC button and press the PLAY button.
3.
Pause recording.
• Press the PAUSE button.
4.
Resume recording.
• Press the PLAY button.
5.
Stop recording.
• Press the STOP button.
When the INDEX WRITE item of the SYSTEM (1/2) menu is
set as ON, an index signal is recorded at the starting position
of recording.
In the PLAYBACK mode, the position where the index signal is
recorded can be detected. (Index search)
Ⅵ During recording, please press the REC button to record
the index signal.
*Please allow at least an interval of 1 minute between recording of
index signals.
Recording of index signals after tape recording is not possible.
Recording index signals
Memo
If recording is executed right
after the RECORDING
PAUSE state, index signals
will not be recorded.