Filter
Top Products
36
RECORDING
–
Setting time codes
–
This unit has a built-in time code reader/ generator. It records time codes during recording. It
does not record the user’s bit.
Time codes are recorded according to the recording condition as follows:
Time codes are recorded in the REC RUN mode. (REC RUN: time codes run only during
recording.)
Time code recording
Time codes are preset via the TIME CODE menu. It can be
set via either the remote controller or the Main unit.
Ⅵ Press the OPERATE button on the Main unit or the
remote controller to turn on the power and set the
unit to the STOP mode.
*To set it with the main unit, first remove the cassette from the
unit if it is loaded.
Condition Time code recording
Time code is preset with this unit.
Time code is not preset.
Preset time codes.
SET
MENIU
EJECT
REC PLAY
PAUSE
REW
STOP
FF
DVCAM NTSC
PAL
REC INH.
CH-1/3
CH-2/4
BR-DV3000
B
SEL.
E
Y/C
PLAY button
EJECT button
PAUSE button
FF button
STOP button
REW button
DISPLAY
BARS
MENU SEARCH+
SEARCH–
SET
BLANK
STILL
MODE
AUDIO
MUTING
OUT SEL.
OUT LEV.
MENU
button
button
button
button
button
SET button
•Time codes preset in the built-in time code generator are re-
corded. (First time only)
•When recording ends, the set time codes becomes void and
regeneration occurs.
Memo
The framing mode is selected from the NDF/DF item of the TIME
CODE menu. (NTSC only)
•It reads the time codes recorded on the tape and continues
recording time codes from these values. (Regeneration)
•If no time code is recorded, it starts from “00”.
*Sometimes, the time codes recorded at the beginning of the
tape may not be read.
Memo
When the REC button is held
down in the STOP mode, the
value of the built-in time code
generator is displayed.
37
–––MENU–––
SYSTEM..
REMOTE. .
AUDIO/VIDEO. .
TIME CODE. .
DISPLAY SET..
CLOCK ADJUST..
FACTORY SETTING CANCEL
DRUM HOURMETER 000000
EXIT
TOP MENU
–––TIME CODE–––
TC 00:00:00:00
CLEAR CANCEL
NDF/DF(NTSC) DROP
TC DUPLICATE OFF
TC ADJUST(DV) OFF
PAGE BACK
Time Code
Hour Second
Minute Frame
Framing mode
(NTSC only)
TIME CODE MENU
1.
Display the TOP MENU.
Main unit
Press the EJECT button for at
least 2 seconds.
Remote controller
Press the MENU button.
Memo
If the REC button is held down in the STOP mode when the TC DUPLICATE item is set to AUTO or NON DROP, the
EE signals of the time codes from the DV input terminal can be checked.
Ⅵ Resetting the time code
to zero:
1
Select the CLEAR menu
item.
2
Set the value to EXECUTE
and press the SET button
(remote controller) or the
PAUSE button (Main unit).
Memo
Framing mode (NTSC only)
DROP
: Time codes that match
the actual time.
NON DROP
: Use this setting if the
number of frames is im-
portant.
2.
Display the TIME CODE menu.
Main unit
Select the TIME CODE item
with the PLAY/STOP button
and press the PAUSE or FF
button.
Remote controller
Select the TIME CODE item
with the
ᮡ
/
ᮢ
button and
press the SET or
ᮣ
button.
3.
Preset the time code (hour, minute, second and frame).
Main unit
1
Select the TIME CODE item
with the PLAY/STOP button
and press the PAUSE or FF
button.
2
Press the FF or REW but-
ton to shift to the next digit
segment
3
Press the PLAY/STOP but-
ton to change the value of
the blinking digits.
4
Repeat
2
and
3
steps
above and set all the values.
Press the PAUSE button.
Remote controller
1
Select the TC item with the
ᮡ
/
ᮢ
button and press the
SET or
ᮣ
button.
¥ The hour digits blink.
2
Press the
ᮣ
/
ᮤ
button to
shift to the next digit seg-
ment.
3
Press the
ᮡ
/
ᮢ
button to
change the value of the
blinking digits.
4
Repeat steps
2
and
3
above and set all the val-
ues. Press the SET button.
4.
Set the framing mode (NON DROP / DROP) ... (NTSC only)
Main unit
1
Select the NDF/DF item with
the PLAY/STOP button and
press the SET or FF button.
2
Press the PLAY/STOP but-
ton to select the value.
3
Press the PAUSE button to
confirm the setting.
Remote controller
1
Select the NDF/DF item
with the
ᮡ
/
ᮢ
button and
press the SET or
ᮣ
button.
2
Press the
ᮡ
/
ᮢ
button to
select the value.
3
Press the SET button to
confirm the setting value.
5.
Return to the usual screen.
Main unit
Press the EJECT button.
Remote controller
Press the MENU button.
Recording time codes of a DV input terminal:
• Set the TC DUPLICATE item of the TIME CODE menu to AUTO.
•To record time codes in the non-drop frame mode from BR-DV600, GY-DV500 or GY-DV700W,
set the TC DUPLICATE setting to NON DROP.