Filter
Top Products
20
ON-SCREEN DISPLAY
–
Status display
–
(continued)
No. Item Content
3
Time code
• It displays the time codes (hour, minute, second and frame).
During playback, the time codes recorded on the tape are
displayed.
TCR : time code reader data
TCG : time code generator data
DTCG : time code data input from a DV IN terminal
• The symbols for the second and frame differ according to the
framing modes. (NTSC only)
00 : 00 : 00 : 00
¥
dot (.) is used for a dropped frame.
colon (:) is used for a non-dropped
frame.
• The time code display position can be set via the COUNTER
POSI. item of the DISPLAY menu.
• The TIME CODE item can be set to turn on/off the time code
display.
• The user’s bit is not displayed.
4
VTR operation mode
It displays the VTR operation modes, including:
PLAY, EJECT, FF, REW, STANDBY-ON, STANDBY-OFF, STILL,
REC, REC PAUSE, A. DUB, A. DUB PAUSE, SHTL (shuttle
search), JOG (F.ADV, R.ADV), BLANK SRH (blank search),
NO CASSETTE (cassette not loaded), OPERATE OFF.
When SHTL or JOG is displayed, the speed will also be dis-
played at the same time.
• The VTR MODE item of the DISPLAY menu can be set to
turn on/off the VTR operation mode display.
Memo
If the display position of the time
code is set to the upper right,
this item will be displayed on the
lower right
32K CH–1/2
SP
000
min
04/01/02 STANDBY
-
OFF
11:20:00 TCR 02:00:00:00
5
4
3
5
Remaining tape
It displays the remaining tape duration (minutes).
If it is not identified, “ ––– ” is displayed.
• The TAPE REMAIN item in the DISPLAY menu can be set to
turn on/off the remaining tape duration display.
• The SP display disappears when the DVCAM cassette is
being played back.
• Please use the remaining tape time as a gauge.
21
ON-SCREEN DISPLAY
–
Event display
–
Ⅵ Event display : When a specific function is in activation or when the operation status is
changed with the remote controller, etc, the events will be displayed at
the positions shown below.
32K CH–1/2
SP
000
min
BLANK SEARCH
INDEX DETECTED
04/01/02 STANDBY
-
OFF
11:20:00 TCR 02:00:00:00
A
B
Ⅵ Display at position A
...Operation in progress
Display Contents
Display Contents
AUDIO OUT
LEVEL NORM
AUDIO OUT
LEVEL ATT
AUDIO OUT CH-1/2
AUDIO OUT CH-3/4
AUDIO OUT MIX
DISPLAY ON
DISPLAY AUTO
DISPLAY OFF
FIELD STEP
1ST FIELD STILL
2ND FIELD STILL
FRAME STILL
The standard level of the
playback or EE audio level is
set to NORMAL or ATT with
the remote controller.
The playback audio channel is
set to CH1/2, CH3/4 or MIX
with the remote controller.
The on-screen display is
turned on with the remote
controller.
The on-screen display is set
to AUTO with the remote
controller. In the AUTO
mode, the on-screen display
is shown for about 4 seconds
between mode switches.
The on-screen display is set
to OFF with the remote con-
troller.
Field by field advance play-
back is selected with the re-
mote controller.
When still or frame advance
playback is selected with the
remote controller, the type of
still image is displayed.
•1st FIELD STILL
•2nd FIELD STILL
•FRAME STILL
BLANK SEARCH
INDEX + 1
INDEX MARK
Blank search in progress.
Index search in progress.
The number indicates the
index search position.
When an index is written on
the tape during recording.
Ⅵ Display at position B
...Display for about 3 seconds
Display Contents
INDEX DETECTED
VIDEO END
DETECTED
AUDIO MUTING
ON
AUDIO MUTING
OFF
Index is found during an in-
dex repeat operation.
Video end is found during a
video end repeat operation.
Audio is muted with the re-
mote controller.
Audio is de-muted with the
remote controller.