Filter
Top Products
51
• REM STOP SEL:
Use this menu item to set the operation mode upon reception of a
standby-on signal.
EE : EE mode (STOP mode)
PB : PLAYBACK mode (STILL mode)
• PB START DELAY:
Use this menu item to set the edit timing. If delay occurs at the
start of editing, correct this time discrepancy by adjusting the tim-
ing for starting playback.
0F : No compensation. Usually, this option is selected.
1F to 15F : Delay by the number of frames set by the user. In the
case that the unit is connected to an editing remote
controller with no BUMP function, use this setting to
adjust editing precision.
• SYNCHRONIZATION
Use this menu item to turn on/off the synchronize function (BUMP)
to enhance editing precision.
OFF : No adjustments to synchronize.
ON : Execute adjustments to synchronize. The editing operation
may take more time.
• CONTROLLER SEL [REMOTE (2/2) menu]
Use this menu item to set the type of controller connected.
(
☞
Page 60)
Set it to TYPE 1 when RM-G820 is used.
Ⅵ Setting the TC ADJUST item of the TIME CODE menu
To edit DV signals, set the timing of the time code output from BR-
DV3000 to the editing controller.
• Usually, it is set to 0F.
•To edit DV signal with D9 VTR (equipped with SA-DV60), set it to
–2F.
Memo
LOCAL FUNCTION
•For controlling with the RE-
MOTE terminal, use this
menu item to select the
buttons on the unit to be
rendered operable.
REM FF/REM MODE:
• Use this menu item to se-
lect the action to be ex-
ecuted when an FF or
REW command is received
during playback. (FF/FEW
or search)
–––REMOTE[1/2]–––
REMOTE ON
LOCAL FUNCTION ALL KEYS
PREROLL 5S
REM FF/RE
WMODE FF/REW
REM STOP SEL EE
PB START DELAY OF
SYNCHRONIZATION ON
NEXT PAGE
PAGE BACK
REMOTE (1/2) menu
Notes
• Please do not use this unit as a recorder.
• It does not support AB roll editing.
• It does not support the following editing tasks.
Variable search
Slow-motion edit
CTL edit
• When performing jog operation using the editing remote controller, do it slowly. Otherwise, the VTR
may not be able to keep up.
•For certain controllers, the LEARN function will not work normally.
SONY : RM-450, PVE-500
Enabling the LEARN function:
Insert the tape with time code recorded till 23:59:00:00~00:01:00:00 into the BR-DV3000 before acti-
vating the LEARN function.
RM-G820 Settings
PREROLL : At least 7 sec is recommended.
BUMP : ON
COUNTER : LCT (Player)
After setting has been done, activate the LEARN function.
MENU NO. 18 BUMP SELECT
Select PLAYER if the recorder used is not equipped with the BUMP function.
50
Cut-edit system
This unit can be used as a feeder (player) for an editing system that uses a RS-422A-compat-
ible editing remote controller (RM-G820).
ⅥApplicable model
Editing remote controller
: RM-G820
Recorder : VHS/S-VHS....... BR-S800 (equipped with SA-K26 or SA-R50), BR-S822
* DV signals cannot be input.
D9 (digital S) ..... BR-D80, BR-D85, BR-D750
* To input DV signals, please install SA-DV60 to D9VTR.
EDIT
–
Using the unit in an editing system
–
Example of connection
DV IN/OUT
AUDIO VIDEO
LINE
Y/C
CH 1/3 CH 2/4
INOUT
REMOTE
SERIAL
9PIN
NTSC/PAL
NTSC PAL
DC12V
Y/C IN
VIDEO
LINE OUT
9PIN
Remote controller
REFERENCE IN
RM-G820
9PIN
Y/C OUT
Video
Audio
Player (BR-DV3000)
Recorder
LAP
IN OUT SERVO LAP
IN OUT SERVO
LAP
RESET
LAP
RESET
TOTAL
RECORDER
EJECT
PLAYER
EJECT
P
AUX
CONTINUE
START
END
V.SPEED
EVENT
RENUMBER
RIPPLE
MAN.TAKELEARN
MENU
REC
REW FF STOP
STB OFF
SEARCHPAUSE
/STILL
PLAY
REC REW FF STOP
STB OFF
SEARCHPAUSE
/STILL
PLAY
ASSEM
VIDEO
AUD-1
AUD-2
SPLIT
TC
SPLIT
CANCEL
LAST
ED
REC
EE
OUT
IN
OUT
IN
ENTRY
PREVIEW
AUTO EDIT
GOTO REVIEW
SHIFT
ALL STOP
MAX
MIN
MONITOR
MAX
MIN
MONITOR
FWD
REV
STILL
X-1
X1
FWD
REV
STILL
X-1
X1
RECORDER
PLAYER
HOUR MIN SEC
FRAME
HOUR MIN SEC
FRAME
PR
VITC
LTC
CTL
VITC
LTC
CTL
BUMP
PREROLL
7
5
3
ON
OFF
EVENT No.
V.SPEED
A.SPLIT
DURATION
IN
OUT
IN
OUT
EDITING CONTROL UNIT
RM—G820
+–
Memo
If editing precision is critical, please input the com-
posite signals of the VIDEO LINE OUT of BR-DV3000
as standard synchronization signals into the editing
remote controller. Use the Y/C OUT terminal for video
signals.
Setting the main unit
Mini
PROFESSIONAL
S
ME
EJE
REC PLAY
PAU
REW
STOP
F
DVCAM NTSC
PAL
REC INH.
CH-1/3
CH-2/4
BR-DV3000
A.DUB
OPERATE
INPUT SEL.REMOTE SEL.
MIC
SERIAL
WIRELESS
9PIN
LINE
DV
Y/C
REMOTE SEL.
switch
ⅥSet the REMOTE SEL. switch of the front
panel to 9 PIN.
ⅥSet the NTSC/PAL switch according to
the playback signals.
ⅥSet the REMOTE menu.
• REMOTE : Set it to ON.
• PREROLL : Set the pre-roll time (second).
The setting is recommended to
be at least 7 seconds.
Memo
The setting will be that which is set (if any) via
the editing remote controller.