Filter
Top Products
29
8 SELECTIVE CALL
CTCSS FREQ. ID SCAN
This function scans through all CTCSS frequencies to
identify the incoming CTCSS frequency on the
received signal. You may find this useful when you
cannot recall the CTCSS frequency that the other
persons in your group are using.
1 While the CTCSS function is ON, press [F],
[TONE] (1 s) to start the CTCSS Freq. ID Scan
function.
• To reverse the scan direction, turn the Tuning
control or press [ ]/ [ ].
• To quit the function, press [ ] or [PTT].
• When a CTCSS frequency is identified, the
identified frequency appears and blinks.
2 Press [ ] or [MNU] to program the identified
frequency in place of the current CTCSS
frequency. Otherwise, press [ ] if you do not
want to program the identified frequency.
• Turn the Tuning control or press [ ]/ [ ] while
the identified frequency is blinking to resume
scanning.
Available CTCSS frequencies
.oN
.qerF
)zH(
.oN
.qerF
)zH(
.oN
.qerF
)zH(
.oN
.qerF
)zH(
100.76214.79323.141435.602
203.96310.001422.641537.012
309.17415.301524.151631.812
404.47512.701627.651737.522
500.77619.011722.261831.922
607.97718.411829.761936.332
705.28818.811928.371048.142
804.58910.321039.971143.052
905.88023.721132.681241.452
015.19128.131238.291
118.49225.631335.302
Note:
◆
Received signals are monitored through the speaker while
scanning is in progress.
◆
CTCSS Freq. ID Scan does not scan the tone if a signal is not
detected.
◆
If the CTCSS function is activated for both the A and B-band, the
scan speed may be slower.
DCS
DCS is similar to CTCSS. However, instead of using
an analog audio tone, it uses a continuous sub-
audible digital waveform that represents a 3-digit
octal number. You can select a DCS code from
among the 104 DCS codes listed in the table below.
USING DCS
Press [TONE] until “DCS” appears.
• Each time you press [TONE], the icon cycles as
follows: “ ” (TONE) ➞ “CT” (CTCSS) ➞ “DCS”
(DCS) ➞ “ ” (OFF) ➞ “ ” (TONE).
When the DCS function is ON, you will hear calls only
when the selected DCS code is received. To answer
the call, press and hold the PTT switch, then speak
into the microphone.
Note: You cannot use the DCS function and CTCSS/ Tone functions
simultaneously. Switching the DCS function ON after having
activated the CTCSS/ Tone functions deactivate the CTCSS/ Tone
functions.
SELECTING A DCS CODE
1 While in DCS mode {above}, press [F], [TONE].
• The current DCS code appears.
2 Turn the Tuning control or press [ ]/ [ ] to select
your desired DCS code.
• The available DCS codes are shown in the
following table.
320560231502552133314564216137
520170431212162233324664426237
620270341322362343134305726437
130370541522562643234605136347
230470251622662153544615236457
630411551342172653644325456
340511651442472463254625266
740611261542603563454235466
150221561642113173554645307
350521271152513114264565217
450131471252523214464606327
3 Press [ ] or [MNU] to store the new setting.
Otherwise, press [ ] or [PTT] to cancel.