Filter
Top Products
13
5 OPERATING THROUGH REPEATERS
■ Activating Tone Function
Press [TONE] to switch the Tone function ON (or
OFF).
•“” appears when the Tone function is ON.
Note: You cannot use the Tone and CTCSS/ DCS functions at
the same time. Switching the Tone function ON after activating
the CTCSS/ DCS deactivates the CTCSS/ DCS function.
TH-F7E only: When you access repeaters that require 1750 Hz
tones, you need not activate the Tone function. Press [CALL]
without pressing the PTT switch to transmit a 1750 Hz tone
(default setting).
■ Selecting a Tone Frequency
1 While the Tone function is ON, press [F],
[TONE].
2 Turn the Tuning control or press [ ]/ [ ] to
select the desired tone frequency.
3 Press [ ] or [MNU] to complete the setting.
Otherwise, press [PTT] to cancel.
Available Tone Frequencies
.oN
.qerF
)zH(
.oN
.qerF
)zH(
.oN
.qerF
)zH(
.oN
.qerF
)zH(
100.76214.79323.141435.602
203.96310.001422.641537.012
309.17415.301524.151631.812
404.47512.701627.651737.522
500.77619.011722.261831.922
607.97718.411829.761936.332
705.28818.811928.371048.142
804.58910.321039.971143.052
905.88023.721132.681241.452
015.19128.131238.291
118.49225.631335.302
Note: 42 different tones are available for the transceiver. These
42 tones includes 37 EIA standard tones and 5 non-standard
tones.
TH-F7E only:
◆
To transmit a 1750 Hz tone, simply press [CALL] without
pressing the PTT switch (default setting). Release [CALL] to
quit transmitting. You can also make the transceiver remain
in the transmit mode for 2 seconds after releasing [CALL]; a
1750 Hz tone is not continuously transmitted. Access Menu
No. 24 (1750 HOLD) and select “ON”.
◆
If you desire to assign [CALL] for recalling the Call channel
in place of transmitting the 1750 Hz tone, access Menu
No. 23 (CALL KEY) and select “CALL”.
AUTOMATIC REPEATER OFFSET
This function automatically selects an offset direction,
according to the frequency that you select on the
2 m and 1.25 m (TH-F6A only) bands. The
transceiver is programmed for offset direction as
shown below. To obtain an up-to-date band plan for
repeater offset direction, contact your national
Amateur Radio association.
TH-F6A (U.S.A. and Canada)
This complies with the standard ARRL band plan.
+
–
––
+
S
S
SS
144.0 145.5 146.4 147.0 147.6
145.1 146.0 146.6 147.4 148.0 MHz
S: Simplex
S
S: Simplex
–
222.0
225.0 MHz
223.920
TH-F7E (Europe/ Others)
S
S
S: Simplex
–
144.0
146.0 MHz145.8145.6
Note: Automatic Repeater Offset does not function when Reverse is
ON. However, pressing [REV] after Automatic Repeater Offset has
selected an offset (split) status, exchanges the receive and transmit
frequencies.
1 Press [MNU].
2 Turn the Tuning control or press [ ]/ [ ] to select
Menu No. 5 (AUTO OFFSET).
3 Press [ ] or [MNU].
4 Turn the Tuning control or press [ ]/ [ ] switch
the function ON or OFF.
5 Press [ ] or [MNU] to store the setting.
Otherwise, press [PTT] to cancel.
Note: If you select the frequency within the amateur radio band on
the B-band, the Automatic Repeater Offset function is also activated
in any modes.