Filter
Top Products
Advanced Operations
60
With one stroke of the button, all of contents in the disc° are
automatically dubbed onto the tape.
° The available disc for dubbing onto the tape are DVD-RAM and
non-finalized DVD-R. If you want to dubbing from DVD-Video or
finalized DVD-R, perform Manual Dubbing. (l 61)
Preparation
DVD (Recording source)
≥Press [DVD].
≥Insert the disc containing the programme to be copied. (l 17)
≥Playing back DVD.
≥Press [AUDIO] to select the audio you wish to record.
≥Stop the disc. (l right)
VHS (Recording target)
≥Press [VHS].
≥Insert a video cassette with an intact erasure prevention tab.
(l 50)
≥Confirm that the remaining tape time is sufficient for recording.
(l 57)
≥Select the recording mode.
Settings (“TV System” l 45)
≥When dubbing an NTSC disc to a tape
-
Set “TV System” on “Connection” in “SETUP” to “NTSC”.
≥When dubbing a PAL disc to a tape
-
Set “TV System” on “Connection” in “SETUP” to “PAL”.
∫To stop dubbing halfway through
Press [∫, STOP].
∫When starting the One Touch Dubbing from desired
title
During playing back DVD, press [∫, STOP] on the desired title
(Resume Function l 18), and then press [VHS —, DUBBING], it will
start dubbing from the beginning of desired title.
≥When starting dubbing from the beginning of DVD, cancel the
resume function (l 18) and then press [VHS —, DUBBING].
∫When dubbing is started, the following operations also
start automatically:
≥“On-Screen Messages” on Display ) “Off” (l 45)
≥Recording channel indication on VHS ) “DC” (l 61)
≥Output to TV ) VHS output
≥The audio mode of the target tape is fixed to “LR”.
∫Only the following operations are allowed while
dubbing:
≥Stopping dubbing by pressing [∫, STOP].
≥Switching the audio mode by pressing [AUDIO]. The audio which
you are hearing is recorded.
Note
≥You cannot operate for dubbing while timer recording standby on
both DVD and VHS. Cancel the timer recording standby.
≥When “DVD / VHS Output” is set to “Manual” (l 43), or when DVD
output is selected in starting dubbing, the output is switched to VHS
automatically at the time when dubbing is started.
-
When the dubbing is already started, you cannot switch the
output manually.
≥When the dubbing is not started or not executed, the “DUBBING”
indicator blinks for about 7 seconds. Check if the unit is properly
prepared.
≥When menu screen appeared on the TV, one touch dubbing cannot
start. One Touch Dubbing can perform start, after return from menu
screen.
Dubbing from DVD
∫ One Touch Dubbing (DVD l VHS)
SLOW/
SEARCH
REW
FF
SKIP/INDEX
PLAY
STOP
PAU SE
FUNCTIONSDIRECT NAVIGATOR
µ
DVD/VHS
CREATE
CHAPTER
TRACKING/V-LOCK
DVD/VHS
CANCEL/RESET INPUT SELECT
DIRECT TV REC
VHS
G-Code
CREATE
CHAPTER
CH
AV
VOLUME
DVD
CH, W, X
DUBBING
AUDIOEXT LINK
VHS REC
DVD REC REC MODE TIMER
VHS
DVD
JET REW
DVD
VHS
1
;
∫
:, 9
AUDIO
REC MODE
VHS —
OPEN/CLOSE
TIME SLIP
REC
CH
/k1.3
DUBBING
VHS
DVD
VHS
DUBBING indicator
[1] While both DVD/VHS are stopped,
Press and hold [VHS —, DUBBING] for
3 seconds or more.
≥Check if dubbing starts properly.
≥On the main unit, press [VHS —].
≥The “DUBBING” indicator on the main unit lights.
≥Dubbing is automatically completed when playback of the
disc is finished or the tape reaches to the end.
≥When dubbing is completed, a message indicating the
end of dubbing appears on the TV screen and then
disappears a few seconds later.
∫About Recording VISS (l 52)
In One-Touch Dubbing from DVD to VHS, the index signal is
automatically recorded for each titles. You can search desired
titles with [: ] or [ 9].
VHSDVD
75VGN.book 60 ページ ２００４年７月２１日 水曜日 午前１１時５４分