Filter
Top Products
80
EN
Additional Information
In case of difficulty
÷ Register its setup code correctly. „
÷ Press the input selector key and select the optimum control mode.
÷ Replace with new batteries.
÷ Point the remote control unit to the remote sensor of the receiver. &
÷ Connect the components properly referring to "Setting up the system"
÷ The remote control has not been set to the operation mode for the component you wish to
control. Press the source select keys or the SRC Power key to activate the operation mode for the
component you want to control before operation. ´
Control of another component is
impossible.
Remote control operation is not
possible.
Remote control unit
Symptom Remedy
Memory back-up function
If the power supply to the receiver is shut down for about a day
or more, the following settings will be reset to the initial condi-
tions. Please be careful.
÷Power mode = OFF
÷Volume level =
-
66 dB
÷Dimmer level = OFF (Brightest condition)
÷Broadcast band = FM
÷Frequency setting = 87.50 MHz
÷Tuning mode = AUTO
As an ENERGY STAR
®
Partner, Kenwood Corpora-
tion has determined that this products meets the
ENERGY STAR
®
guidelines for energy efficiency.
This product can save energy. Saving energy reduces
air pollution and lowers utility bills.
FCC WARNING
This equipment may generate or use radio frequency energy. Changes
or modifications to this equipment may cause harmful interference
unless the modifications are expressly approved in the instruction
manual. The user could lose the authority to operate this equipment
if an unauthorized change or modification is made.
NOTE:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment may
cause harmful interference to radio communications, if it is not
installed and used in accordance with the instructions. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– –
Reorient or relocate the receiving antenna.
– –
Increase the separation between the equipment and receiver.
– –
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
– –
Consult the dealer or an experienced radio / TV technician for help.
For the U.S.A.
Note to CATV system installer
This reminder is provided to call the CATV system installer's attention
to Article 820-40 of the NEC that provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the
point of cable entry as practical.
÷ Connect an antenna properly. &
÷ Set the broadcast band properly.
÷ Tune the frequency of the desired station. ›
÷ Install the outdoor antenna away from the road.
÷ Turn off the power to the appliance.
÷ Install the receiver farther away from the TV.
÷ Preset a station with a receivable frequency.
Radio stations cannot be received.
Interference.
A station which was preset cannot be
received by pressing the corresponding
numeric key.
Tuner
Symptom Remedy
For the U.S.A.
For the U.S.A.
Frequently Asked Questions (FAQ):
If you still have questions concerning the product after reading
this manual, please consult the FAQ section on the KENWOOD
website of your resident country (if necessary you can find a link
to your local website on www.kenwood.com <http://
www.kenwood.com>).
Software and Firmware update:
The latest information and procedure to update your
KENWOOD PC SERVER software and VRS-N8100 Firmware
can be found in the "Technical Support" / "Service" section
on the website of your resident country (if necessary you
can find a link to your local website on www.kenwood.com
<http://www.kenwood.com>).
*5489/78-84/EN 04.7.30, 10:41 AM80