Filter
Top Products
23
EN
Preparations
6
Adjust the speaker volume level.
Speaker Level
From your usual listening position, adjust the volume levels. The
volume levels from each speaker should be the same.
÷ In this step 6, only the speaker channels that have been set
and require the volume level adjustment are displayed.
1 Use the MULTI CONTROL @ / # (or the Multi @ / # keys)
to select “Speaker Level” on setup displays, and press
the ENTER (or the Enter key).
2 Use the MULTI CONTROL @ / # (or the Multi @ / # keys)
to select “Test Tone Auto”, “Test Tone Manual “ or
“Test Tone Off”.
Test Tone
Auto
Test Tone
Manual
Exit
Test Tone
Off
T
R
S
E
E
P
S
C
E
T
E
A
I
K
T
V
E
O
E
R
N
R
E
S
L
A
E
E
U
T
V
T
U
E
O
P
L
1 “Test Tone Auto”: Select this setting to adjust the speaker
volume levels using the test tone. The test tone will be output
from every speaker channel in automatic sequence.
2 “Test Tone Manual”: Select the speaker channel to
output the test tone using the MULTI CONTROL@ / #
(or the Multi @ / # key).
3 “Test Tone Off”: Select to adjust the speaker volume
levels using the current output signals. The speaker
channel to output the signal can be selected using the
MULTI CONTROL@ / # (or the Multi @ / # key).
4 “Exit”: Select “Exit” and press the ENTER (or the Enter key)
to return to the previous display.
÷ Press the SETUP (or Setup) key to cancel the SETUP
mode in the middle.
When “
Test Tone Auto
” or “
Test Tone Manual
” is se-
lected and the ENTER (or the Enter key) is pressed again,
the test tone output will start.
Use the MULTI CONTROL % / fi (or the Multi % / fi keys)
to adjust the volume level of the test tone output from
the speaker channel to be adjusted.
For
“
Test Tone Auto
”
selection, the first test tone is
heard from the front left speaker for 2 seconds. The next
test tone is heard from the speakers in the following
sequence for 2 seconds each.
When the “BS/SW Amp Back Surr.” has been selected:
Left Center
Right Right Surround
Left SurroundSubwoofer Back Surround
When the “BS/SW Amp Subwoofer” or “BS/SW Amp
Off” has been selected:
Left Center
Right Right Surround
Left Surround
Left Back Surround Right Back Surround
Subwoofer
R
RS
L
SW
BS
LS
C
Left
0 dB
00 dB
00 dB
00 dB
00 dB
00 dB
00 dB
00 dB
LE
0
F
d
T
B
T
S
E
P
S
E
T
AK
T
E
O
R
NE
L
A
E
U
V
T
E
O
L
÷ If you change the volume level settings for the speakers while
listening to music, the settings referred to on this page are
also changed. e
÷ When a speaker setup is set to off the volume level for
the corresponding speakers is reset to 0 dB.
When “Test Tone Manual” or “Test Tone Off” is se-
lected, press the MULTI CONTROL @/# (or the Multi
@/# key) to select the speaker channel and then
press the MULTI CONTROL %/fi (or the Multi %/fi
key) to adjust the speaker volume level.
R
RS
L
SW
BS
LS
C
Left
0 dB
00 dB
00 dB
00 dB
00 dB
00 dB
00 dB
00 dB
LE
0
F
d
T
B
T
S
E
P
S
E
T
AK
T
E
O
R
NE
L
M
E
A
V
N
E
U
L
AL
3 Press the ENTER (or the Enter key) again to return to
the main setup displays.
÷ The test tone is turned off and return to the main setup
displays.
7
Input the distance to the speakers.
Speaker Distance
This setting allows the signals output from different speakers to
reach the listening position simultaneously.
÷ In this step 7, only the speaker channels that have been set
and require the volume level adjustment are displayed.
Measure the distance from the listening position to each
of the speakers.
Jot down the distance to each of the speakers.
Distance to Front speaker (L) : ____ feet (meters)
Distance to Center speaker (C) : ____ feet (meters)
Distance to Front speaker (R) : ____ feet (meters)
Distance to Surround speaker (RS) : ____ feet (meters)
Distance to Surround back speaker (RB) : ____ feet (meters)
Distance to Surround back speaker (LB) : ____ feet (meters)
Distance to Surround speaker (LS) : ____ feet (meters)
Distance to Subwoofer (SW) : ____ feet (meters)
Preparing for playback
Continued to next page
*5489/18-29/EN 04.7.30, 10:39 AM23