Filter
Top Products
22
EN
Preparations
2 “Front Normal”:
Average size front speakers are connected to the re-
ceiver.
÷ When the subwoofer setting is “Subwoofer On”, front
speakers setting is “Front Large” and a stereo source
is played, the low frequencies may be reproduced
through the front speakers and no audio output from the
subwoofer in certain listen modes. In this case, set the
subwoofer re-mix setting in step # to “SW Re-mix On”
to output the low frequencies from the subwoofer.
4 Use the MULTI CONTROL # (or the Multi # key)
to accept the setting.
5 Use the MULTI CONTROL % / fi (or the Multi % / fi keys)
to select the appropriate center speaker setting.
1 “Center Large”: *
A large center speaker is connected to the receiver.
2 “Center Normal”:
An average size center speaker is connected to the receiver.
3 “Center Off”:
When no center speaker is connected.
*
“Center Large” cannot be selected when the front
speakers have been set to “Front Normal”.
6 Use the MULTI CONTROL # (or the Multi # key)
to accept the setting.
7 Use the MULTI CONTROL % / fi (or the Multi % / fi keys)
to select the appropriate surround speaker setting.
1 “Surround Large”:
Large surround speakers are connected to the receiver.
2 “Surround Normal”:
Average size surround speakers are connected to the re-
ceiver.
3 “Surround Off”:
When no surround speakers are connected.
÷ When “Surround Off” is selected and the selection is
established by pressing the MULTI CONTROL # in step
8 below, the procedure jumps to step #. However, if
the subwoofer setting is “Subwoofer Off”, the proce-
dure jumps to step $ so that you can complete the
speaker setup and proceed to the speaker volume level
adjustment in step 6.
8 Use the MULTI CONTROL # (or Multi # key) to ac-
cept the setting.
9 Use the MULTI CONTROL % / fi (or the Multi % / fi keys)
to select appropriate surround back speaker setting.
1 “Back Surr. Large”: *
Large surround back speaker is connected to the receiver.
2 “Back Surr. Normal”:
Average size surround back speaker is connected to the
receiver.
3 “Back Surr. Off”:
When no surround back speakers is connected.
* “Back Surr. Large” cannot be selected when the sur-
round speaker has been set to “Surround Normal” or
“Surround Off”.
0 Use the MULTI CONTROL # (or the Multi # key)
to accept the setting.
! Use the MULTI CONTROL % / fi (or the Multi % / fi keys)
to select the appropriate BS/SW amp setting.
1 “BS/SW Amp Back Surr.”:
Select this setting when a surround back speaker is con-
nected to the SURR BACK/SW terminals. In this case, the
subwoofer signal will be output from the PRE OUT
SUBWOOFER jack.
2 “BS/SW Amp Subwoofer”:
Select when the subwoofer speaker is connected to the
SURR BACK/SW terminals. In this case, the surround back
signals will be output from the PRE OUT SURROUND BACK
jacks.
3 “BS/SW Amp Off”:
Select when no speaker is connected to the SURR BACK/
SW terminals. In this case, the subwoofer signal will be
output from the PRE OUT SUBWOOFER jack and the sur-
round back signals will be output from the PRE OUT SUR-
ROUND BACK jacks.
÷ If “BS/SW Amp Back Surr.” is selected, only one sur-
round back speaker can be connected to the receiver.
÷ If “BS/SW Amp Subwoofer” or “BS/SW Amp Off” is
selected, two surround back speakers can be connected
to the PRE OUT SURROUND BACK jacks through an
external power amplifier. ^
@ Use the MULTI CONTROL # (or the Multi # key)
to accept the setting.
# Use the MULTI CONTROL % / fi (or the Multi % / fi keys)
to select the appropriate subwoofer re-mix setting.
If “SW Re-mix On” is selected as the subwoofer re-mix
setting, the low frequencies are enhanced by adding the
low frequencies of other channels to the subwoofer chan-
nel or adding the low frequencies of the subwoofer to
other channels depending on the speaker setup.
1 “SW Re-mix On”:
Subwoofer re-mix setting mode to the receiver is ON.
2 “SW Re-mix Off”:
Subwoofer re-mix setting mode to the receiver is OFF.
÷ The initial setting is “SW Re-mix On”.
÷ The subwoofer re-mix setting is possible only when the
subwoofer setting is “Subwoofer On” and the front
speaker setting is “Front Large”.
$ Press the ENTER (or the Enter key). If your selection
is correct, press
the MULTI CONTROL % / fi (or the
Multi % / fi key) to select “Yes”.
Press the ENTER (or the Enter key) again to return to
the main setup displays.
÷ Select “No” and press the ENTER (or the Enter key) to
return to the status before setup.
Preparing for playback
Continued to next page
*5489/18-29/EN 04.7.30, 10:39 AM22