Filter
Top Products
Filename [DVM70S_10Timer Recording.fm]
Masterpage:Left+
48 EN
TIMER RECORDING ON HDD/DVD DECK
Page 48Friday, 6 May 2005 12:06
You can program this unit to timer record as many as 16 programs.
If you do not know the PlusCode number for the program you wish
to record, use the following procedure to set your unit to
timer record the program.
1 Load a recordable disc if recording to DVD.
2 Press PROG to access the program top screen.
3 Press FGDE to select ACALENDAR PR.B, then press ENTER.
● When APROGRAM FULL DELETE UNWANTED TIMER
PROGRAMSB appears on the TV screen, you need to cancel
some of the reserved programs. (A pg. 49)
4 Press FGDE to select the desired date, then press ENTER.
5 Press FG to select ARECORD
TOB, then press ENTER. Press
FG to select the desired
recording deck, then press
ENTER.
6 Press FG to select ASTARTB,
then press ENTER. Press FG
to set the desired start time,
then press ENTER.
● Each press of FG increases/decreases the start time in 1-
minute interval.
● To increase/decrease the start time in 30-minutes interval,
press and hold FG.
7 Press FG to select ASTOPB, then press ENTER. Press FG to
set the desired stop time, then press ENTER.
● Each press of FG increases/decreases the stop time in 1-
minute interval.
● To increase/decrease the stop time in 30-minutes interval,
press and hold FG.
8 Press FG to select ASOURCEB, then press ENTER. Press FG
to select the desired source.
9 Press FG to select ACHB, then press ENTER. Press FG to
select the desired channel.
10 Press FG to select ACONFIRMB, then press ENTER.
11 Set the other recording options as required.
● Refer to step 8 in AVCR Plus+ Timer ProgrammingB
(A pg. 46).
12 Press FG to select AOKB,
then press ENTER to access
the Program Confirmation
screen.
13 Press DE to select AEXITB,
then press ENTER to
complete timer
programming.
● To program another timer,
press DE to select ACONTINUEB, then press ENTER.
● If APROGRAM OVERLAPPEDB appears on the TV screen,
delete or modify the programs.
NOTES:
● When two successive programs are recorded on a DVD-RW disc
with Manual Timer Programming function, the beginning of the
second one may be left off the recording.
● If the copy limited program is received during timer-recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you
programmed.
Manual Timer Programming
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
FGDE
PROG
ENTER
CABLE/DBS
DVDTV
HDD
DBS 100
[MISC. ] XP
100
CATV
11:00PM
10:30PM
2
PROGRAM > CALENDAR PR. (2/3)
CONFIRM
01/08/03 WED 10:30PM - 11:00PM
RECORD TO
STOP
START
SOURCE
ENTER
SELECT
PROG
EXIT
PRESS [PROG] TO EXIT
SELECT WITH @
THEN PRESS [ENTER]
CH
Cable box and DBS Receiver Users
To timer record a satellite broadcast using Manual Timer
Programming:
A Perform AManual Timer ProgrammingB (A pg. 48).
B Set the cable box or DBS receiver to the appropriate channel
before the selected program begins.
C Leave the cable box or DBS receiver’s power on.
Relief Recording
When a program that is set for the DVD deck cannot be
recorded properly, the program is recorded to the HDD deck
instead in XP mode.
● If the remaining capacity of the hard disc is not sufficient, the
program is recorded to the DVD deck until the remaining
capacity of the DVD disc lasts.
● If AJUSTB is selected for the recording mode, the current
recording mode for the DVD deck is applied.
1:00 28:00
DBS 100
2
ENTER
SELECT
PROG
EXIT
PROGRAM > CALENDAR PR. (3/3)
PRESS [PROG] TO EXIT
SELECT WITH @
THEN PRESS [ENTER]
OK
INPUT NAME
CATEGORY
WEEKLY/DAILY
REC MODE
GARDENING
EDUCATION
MON-FRI (FOR A WEEK)
FR360
01/08/03 WED 10:30PM - 11:00PM
GARDENING [EDUCATION]
FR360
DVM70S_00.book Page 48 Friday, May 6, 2005 12:06 PM