Filter
Top Products
Masterpage:Right0
EN 19
Filename [DVM70S_05Name.fm]
Page 19 Friday, 6 May 2005 12:06
INITIAL SETTINGS
Auto Clock Set/Auto Tuner Set
This unit sets the clock and tuner channels automatically when AC
power cord is first connected to an AC outlet. The antenna cable
must be connected for the Plug & Play setting.
The time and date can be set automatically by the clock setting
data transmitted from one of the regular TV broadcast channels.
We call this TV channel the “host channel” and it is a PBS channel
in your area.
1 Connect the antenna cable to the unit. (A pg. 18) Then connect
the AC power cord to an AC outlet. Do not turn on the unit.
The clock and tuner channels will be set automatically.
● ALOADINGB blinks on the front display panel when the AC plug
of the AC power cord is connected into an AC outlet and it takes
approximately 50 seconds for the unit to be turned on. This is
not a malfunction.
NOTES:
● Auto Clock Set is performed first.
AAUTOB blinks on the front display panel during Auto Clock Set.
● Auto Channel Set is performed next. Auto Channel Set scans all
the channels that are receivable by your unit. During Auto
Channel Set, the channel numbers are displayed as they are
scanned and set.
● When Plug & Play setting has been completed successfully, the
correct clock time is displayed. If you perform Plug & Play setting
successfully, there is no need to perform AClock SetB (A pg. 21)
and ATuner SetB (A pg. 22). If, however, you want to add or
delete channels, refer to AManual Channel SetB (A pg. 22).
Plug & Play Set
ATTENTION:
● If you use a cable box, Plug & Play will not function; set the
clock and tuner channels separately. (੬ pg. 21 – 22)
● Depending on areas or reception conditions, the unit may not
receive the Auto clock setting data from the PBS channel. If
this function is taking a considerable amount of time, it may be
necessary to perform the Semiauto or Manual Clock Set
procedure.
INFORMATION
● If AAUTO CLOCKB is set to AONB (A pg. 21), the clock will be
adjusted automatically by the host channel every hour (except
11:00 PM, midnight, 1:00 AM and 2:00 AM) using the incoming
PBS channel clock setting data. (This automatic clock
adjustment can only be performed when the unit is turned off.
The clock will be adjusted just on these hours — on the time
displayed on the front display panel, not on the actual real
time.) The default setting of AAUTO CLOCKB is AONB.
(A pg. 21)
● If the memory backup fails, because a power outage occurs or
because the AC power cord is unplugged, Plug & Play will be
performed when power is restored to the unit.
What to do if Plug & Play setting failed
● If an incorrect time is displayed on the front display panel, you
may be receiving the clock setting data of a PBS channel from
an adjacent time zone, or an incorrect PBS channel from a
cable TV system. In this case, perform ASemiauto Clock SetB
(A pg. 21) or AManual Clock SetB (A pg. 21).
● If AcB appears on the front display panel, your antenna
cable may not be connected to the unit or there may not be a
Host PBS signal available in your area. Ensure that the
antenna cable is connected correctly. Then turn on and off the
unit; the Plug & Play setting will be automatically reactivated. If
Plug & Play setting is not performed though the antenna cable
is connected correctly, perform AManual Clock SetB (A pg. 21)
and AAuto Channel SetB (A pg. 22) or AManual Channel SetB
(A pg. 22).
During Auto Clock Set
AAUTOB blinks.
During Auto Channel Set
The channel numbers are displayed and AAUTOB blinks as they
are scanned and set.
Plug & Play Completed
The current time is displayed.
● If an incorrect clock time or AcB appears on the front display
panel, see AWhat to do if Plug & Play setting failedB (A pg. 19).
DVM70S_00.book Page 19 Friday, May 6, 2005 12:06 PM