Filter
Top Products
Filename [MX1S_09Timer Recording.fm]
Masterpage:Left+
62 EN
TIMER RECORDING ON VHS DECK
Page 62Saturday, 30 October 2004 16:18
Check, Cancel And Change Programs
1 When the VHS recording lamp (7) lights up on the unit
Press VHS TIMER, then press DVD (1).
When the VHS lamp does not light up on the unit
Press VHS so that the VHS lamp lights up on the unit.
2 Press PROGRAM to access the
Program screen.
3 Press rt to select “PROGRAM/
CONFIRM”, then press ENTER to
access the Program Check screen.
4 Press rt to select the program,
then press ENTER. The program
screen appears.
To cancel a program
Press CANCEL.
5 Change the settings of the desired recording options as
required.
● Refer to steps 6 - 11 in “Manual Timer Programming” (੬ pg. 61).
6 Press PROGRAM to complete timer correction. The previous
screen resumes.
7 Press VHS TIMER.
● The VHS recording lamp lights up on the unit and the HDD or DVD
deck is automatically selected. When the HDD or DVD deck is in
timer standby mode, the unit is automatically turned off.
When Programs Overlap Each Other
If “PROGRAM NOT COMPLETED PROGRAM OVERLAP”
appears, you have another program overlapping the program you
have just made.
The Program Check screen appears and conflicting programs will
start blinking.
Example: Program 1 (you have just made) and Program 4
overlap each other.
1 Confirm the overlapping programs. Overlapping programs blink
on the TV screen.
2 Press rt to select the program to modify, then press ENTER
or e.
● You can only select one of the overlapping programs.
NOTE:
If you do not mind this overlap, press PROGRAM to finish the timer
program setting. The program with the lower program number will be
recorded and the other one will not be recorded correctly. If no changes
are made for approximately 1 minute, the unit will return to the normal
screen.
3 Press rt to select the desired program to be canceled or
changed.
To cancel the program
Press CANCEL.
● “PROGRAM COMPLETED” appears on the TV screen for about 5
seconds, then the normal screen resumes.
To change the program setting
Press ENTER, then go to step 4.
4 Change the program setting.
● Refer to steps 6 - 11 in “Manual Timer Programming” (੬ pg. 61).
5 Press PROGRAM to access the Program screen, then press
rt to select “PROGRAM/CONFIRM” to check if the conflict has
been settled.
Program check screen appears.
● “PROGRAM COMPLETED” appears on the TV screen for about 5
seconds, then the normal screen resumes.
6 Press VHS TIMER.
NOTE:
When any overlaps remain after deletion and modification of programs,
Program Check screen remains showing the conflicting programs. In
such a case, repeat the procedure above until the conflict is solved.
rtwe
PROGRAM
ENTER
CANCEL
VHS
VHS TIMER
1
CABLE/DBS
DVDTV
(PROGRAM) TO END
PR START STOP CH DATE
1 8:00P 10:00 12 12/24
2 10:00A 10:45 40 12/25
3 11:30P 1:00 125 12/25
4
5
6
7
8
PROGRAM 4
START STOP
8:00AM 10:00AM
DATE CH SP/EP
12/24/04 12 SP
FRI
PRESS (CANCEL) TO CANCEL
PRESS (ENTER) TO CONFIRM
(PROGRAM) TO END
( )](ENTER) (PROGRAM) : END
PR START STOP CH DATE
1 8:00P 10:00 12 12/24
2 10:00A 10:45 40 12/25
3 11:30P 1:00 125 12/25
4 9:00P 10:00 10 12/24
5
6
7
8
PROGRAM NOT COMPLETED
PROGRAM OVERLAP
MX1S_00.book Page 62 Saturday, October 30, 2004 4:18 PM