Filter
Top Products
21
Troubleshooting chart (continued)
USB
Symptom Possible cause
z Device cannot be
detected.
z There is no MP3/WMA fi le
inside the device.
z The device is not properly
connected.
zA MTP device is connected.
z The device contains AAC fi le
only.
z Playback does not start. zA copyright-protected WMA or
false MP3 fi le is being played
back.
z Wrong time display.
z Wrong fi le name display.
zA Variable Bitrate fi les are being
played back.
z The File Name was written in
other than English characters.
iPod, iPhone or iPad
Symptom Possible cause
z No sound is produced.
No image appears on
the TV/monitor.
z The iPod, iPhone or iPad is not
playing.
z The iPod, iPhone or iPad is not
properly connected to the unit.
z The AC power lead of the unit is
not plugged in.
z The video cable is not properly
connected.
z The TV/monitor’s input
selection is not properly set.
z The iPod TV out feature has not
been set to output video.
z USB terminal do not support
video.
z iPod, iPhone or iPad will
not charge.
z The iPod, iPhone or iPad is
not making full contact with the
connector.
z Using iPod (3rd generation).
z The iPod or iPhone is not
supported. Refer to page 7 for
compatible models.
z “This accessory is
not made to work
with iPhone” or “This
accessory is not
supported by iPhone”
appears on iPhone
screen.
z The iPhone battery is low.
Please charge the iPhone.
z iPhone is not properly docked.
Condensation
Sudden temperature changes, storage or operation in an
extremely humid environment may cause condensation inside
the cabinet (CD pickup, etc.) or on the transmitter on the remote
control. Condensation can cause the unit to malfunction. If this
happens, leave the power on with no disc in the unit until normal
playback is possible (about 1 hour). Wipe off any condensation on
the transmitter with a soft cloth before operating the unit.
If problem occurs
When this product is subjected to strong external interference
(mechanical shock, excessive static electricity, abnormal supply
voltage due to lightning, etc.) or if it is operated incorrectly, it may
malfunction.
If such a problem occurs, do the following:
1 Set the unit to the stand-by mode and turn the power on again.
2 If the unit is not restored in the previous operation, unplug and
plug in the unit again, and then turn the power on.
Note:
If neither operation above restores the unit, clear all the memory
by resetting it.
Factory reset, clearing all memory
1 Press the ON/STAND-BY button to enter the power stand-by
mode.
2 Whilst pressing down the VOLUME + button, press the ON/
STAND-BY button until “RESET” appears.
Caution:
This operation will erase all data stored in memory including clock,
timer settings and tuner preset.
Care of compact discs
Compact discs are fairly resistant to damage, however mistracking
can occur due to an accumulation of dirt on the disc surface.
Follow the guidelines below for maximum enjoyment from your
CD collection and player.
z Do not write on either side of the disc, particularly the non-label
side from which signals are read. Do not mark this surface.
z Keep your discs away from direct sunlight, heat, and excessive
moisture.
zAlways hold the CDs by the edges. Fingerprints, dirt, or water on
the CDs can cause noise or mistracking. If a CD is dirty or does
not play properly, clean it with a soft, dry cloth, wiping straight
out from the centre, along the radius.
NO YES
Correct
Maintenance
Cleaning the cabinet
Periodically wipe the cabinet with a soft cloth and a diluted soap
solution, then with a dry cloth.
Caution:
z Do not use chemicals for cleaning (petrol, paint thinner, etc.). It
may damage the cabinet.
z Do not apply oil to the inside of the unit. It may cause
malfunctions.
GX-M10H_OM_UK_SCA.indd Sek1:21GX-M10H_OM_UK_SCA.indd Sek1:21 2012-08-17 00:07:552012-08-17 00:07:55