Filter
Top Products
Masterpage:Right-NoTitle0
EN
63
Filename [DVS3U_3-EN.fm]
Page 63 January 10, 2002 10:43 am
A
Make connections.
Connect the player’s VIDEO OUT or S-VIDEO OUT and
AUDIO OUT connectors to your VCR’s VIDEO or
S-VIDEO and AUDIO input connectors.
B
Set the VCR’s input mode.
Press
AUX
(
number key
“
0
”) and/or
CH +/–
to select
“F-1” (or “L-1” if you use the connectors on the rear).
● When using S VIDEO connector, set “FRONT AUX INPUT” (or
“REAR AUX INPUT” if you use the connectors on the rear) to
“S-VIDEO”. (
੬
pg. 71, 73)
● When using VIDEO connector, set “FRONT AUX INPUT” (or
“REAR AUX INPUT”) to “VIDEO”. (
੬
pg. 71, 73)
C
Select the recording deck.
Press
S-VHS
or
DV
.
● When using the DV deck as the recording deck, press so
that the video and audio signals from the VIDEO/S-VIDEO and
AUDIO L + R input connectors can be recorded. The dubbing
direction indicator ( S-VHS) lights.
D
Prepare the recording cassette.
For the VHS deck
Load the recording cassette into the VHS deck, and play
it back to determine the edit-out point (the end of the
segment to be replaced) using the
ADVANCED JOG
dial,
or pressing
w
e
and
PAUSE
(
9
).
Then press
C.RESET
to reset the counter.
For the DV deck
Load the recording cassette into the DV deck.
E
Locate the start point.
Determine the edit-in point (the beginning of the segment
to be replaced) using the
ADVANCED JOG
dial, or
pressing
w
e
and
PAUSE
(
9
).
● Be sure to engage the Still mode at the edit-in point.
F
Engage the Insert Editing mode.
Press
INSERT
.
● Your VCR enters the Insert Pause mode. (“o
”, “
u
” and “
i
”
light up on the front display panel.)
● The TV screen changes from the still picture to the input
source you are going to record.
G
Start Editing.
Load the source cassette and play back the segment that
is to be inserted. When you reach the start of the section
of the source tape that you wish to insert, press
PLAY
(
4
)
to start the tape in your VCR; Insert Editing begins at this
point.
● “
o
” and “
u
” are displayed on the front display panel.
H
End Insert Editing.
For the VHS deck
At counter “0:00:00”, Insert Editing will stop
automatically while the tape continues running in the
Play mode. If you wish to stop Insert Editing before the
specified edit-out point, press
C.RESET
.
For the DV deck
Press
STOP
(
8
) to stop recording on the DV deck.
AV Insert Editing (VHS deck only)
If you want to replace the picture, Hi-Fi audio soundtrack
and normal audio soundtrack all at the same time ...
... In step
6
, after you press
INSERT
, press
A.DUB
also.
(“
o
” and “
u
” blink and “
i
” lights up on the front display
panel.)
NOTES:
●
Once the Insert Editing starts, you can not use the other deck.
●
All necessary cables can be obtained from your dealer.
●
Insert Editing cannot be performed on a VHS (or S-VHS)
cassette that has had its record safety tab removed, or on a
Mini DV cassette that has had its erase protection switch set to
“SAVE”.
●
When Insert Editing is performed on a tape that has been
recorded on another VCR, the inserted portion may appear
distorted.
●
In Insert Editing, the recording speed (SP/EP) is determined by
the previous recording to be replaced. If the previous
recording’s speed changes within a single edit, the inserted
picture will be distorted at the switching point. (VHS deck
only)
●
A small portion of the recording which precedes an insert edit
may become erased.
●
Insert Editing is also possible using the rear panel connectors.
When using these connectors, be sure to set “REAR AUX
INPUT” to the appropriate mode. (
੬
pg. 71)
●
Insert Editing is not possible using the DV IN/OUT connector.
●
Insert Editing is not possible on a blank portion of the tape.
DVS3U_1-EN.book Page 63 Thursday, January 10, 2002 10:51 AM