Filter
Top Products
Masterpage:Right-NoTitle0
EN
47
Filename [DVS3U_2-EN.fm]
Page 47 January 10, 2002 10:51 am
H
Enter the program date.
Press
DATE+/–
.
● The current date appears on the TV screen. The date you enter
appears in its place.
I
Enter the channel position.
Press
CH+/–
.
● If you are using a DBS receiver, see “ATTENTION FOR DBS
RECEIVER USERS” in the right column.
● Holding down
CH +/–
rapidly scans through the channels.
J
Set the tape speed.
For the VHS deck
Press
SP/EP
(
p
).
For the DV deck
Press
SP/LP
(
p
).
K
Return to the normal screen.
Press
PROG
or
OK
. “PROGRAM COMPLETED” appears
on the TV screen for about 5 seconds, then the normal
screen appears. If “PROGRAM NOT COMPLETED
PROGRAM OVERLAP” appears on the TV screen, see
page 51.
● Repeat steps
3
–
11
for each additional program.
L
Engage the VCR’s timer mode.
Press
TIMER
. The VCR turns off automatically and “
#
”
appears on the front display panel.
● To disengage the timer mode, press
TIMER
again.
NOTES:
●
To Timer-Record Weekly Or Daily Serials . . .
...anytime during steps
5
through
10
, press
WEEKLY
(
number key
“
9
”) for weekly serials or
DAILY
(
M–F
) (
number
key
“
8
”) for daily serials (Monday – Friday). Either “WEEKLY”
or “DAILY” appears on the TV screen. Pressing the button
again makes the corresponding indication disappear.
●
You can program each deck to timer-record as many as 6
programs. If you try to program the VCR to record a seventh,
“PROGRAM FULL” appears on the TV screen. To record the
extra program, you must first cancel any unnecessary
programs (
੬
pg. 50).
●
In case of a power failure after programing, the VCR’s memory
backup keeps your selections for approximately 10 minutes.
●
Programs that start after midnight must have the next day’s
date.
●
You can program the timer while a regular recording is in
progress; the on-screen menu will not be recorded.
●
It is not possible to timer-record the same program on both the
VHS deck and the DV deck simultaneously.
●
During timer recording, it is not possible to change the
recording deck (VHS or DV).
●
If the times that are programed for recording on the DV deck
and on the VHS deck overlap, the earlier start time takes
precedence. If the start times are the same, the VHS deck takes
precedence.
Cable Box or DBS Receiver Users
To timer-record a cable or satellite broadcast using Express
Timer Programing:
A Perform “Cable Box Control Setting” on page 20 or “DBS
Receiver Control Setting” on page 23.
B Perform steps
1
–
12
.
C Leave the power of cable box or DBS receiver on.
ATTENTION FOR DBS RECEIVER USERS
If you are using a DBS receiver (unless “DBS RECEIVER SET”
is set to “OFF”
੬
pg. 24), the band indication (TV, CATV or
DBS) appears under the channel number indication.
TV: To timer-record a regular
TV broadcast received
on the VCR.
CATV:To timer-record a cable
TV broadcast received
on the VCR, or through a
cable box (unless
“CABLE BOX SET” is set
to “OFF”
੬
pg. 21).
DBS: To timer-record a satellite broadcast received through
a DBS receiver.
NOTE:
If “BAND” is set to “TV” on the Tuner Set screen (
੬
pg. 18)
and “CABLE BOX SET” is set to “OFF” on the Cable Box Set
screen (
੬
pg. 21), “CATV” will not be displayed on the
Program screen; If “BAND” is set to “CATV” or “CABLE BOX
SET” is set to “ON”, “TV” will not be displayed.
If the channel number entered requires that the band be set,
“7=DBS” is displayed on the screen.
If this happens, press the
number key “7 (DBS)
” to select
“DBS”.
DVS3U_1-EN.book Page 47 Thursday, January 10, 2002 10:51 AM