Filter
Top Products
48 EN
Recording
Perform steps 1 – 4 on page 35 (“Simple Recording”) before
continuing.
ATTENTION
Ⅲ As calibration takes place before recording actually starts,
there is a delay of about 7 seconds after REC and PLAY on
the remote, or REC on the recorder’s front panel, are
pressed. To make sure you record the desired scene or
program completely, first perform the following steps:
1) Press and hold PAUSE, and press REC to engage the
RECORD PAUSE mode.
● The VCR then automatically checks the condition of
the tape and, after about 7 seconds, re-enters
RECORD PAUSE.
2) Press PLAY to start recording.
Ⅲ If you want to bypass Video Calibration and start
recording right away, set “VIDEO CALIBRATION” to
"OFF" in step 3 of the Preparation procedure (੬ pg. 47).
START PLAYBACK
1
Press PLAY.
● The recorder adjusts the
playback picture quality
based on the quality of
the tape in use.
NOTES:
●
When using rental tapes,
or tapes recorded on other VCRs, set “VIDEO
CALIBRATION” in step 3 of the Preparation proce-
dure to either “ON” or “OFF” as desired to give the
best picture (
੬
pg. 47).
●
The Video Calibration screen only appears at the
beginning of automatic tracking. Even though the
screen doesn't appear after that, the Video Calibration
function is operative.
●
To display the Video Calibration screen, “SUPERIM-
POSE” must be set to “ON” or the Video Calibration
screen will not appear (
੬
pg. 41.)
START RECORDING
1
Press and hold REC and
press PLAY on the remote
control, or press REC on
the recorder’s front panel.
● The recorder takes about
7 seconds to assess the
quality of the tape in
use, then recording
begins with the picture
level optimized.
NOTES:
●
Calibration occurs
immediately prior to
both the first SP and the
first EP recording after
inserting the cassette. It
does not take place
during recording.
●
In the case of timer
recording, calibration
takes place for both SP and EP before the first timer
recording after inserting the cassette (regardless of the
tape speed selected for that recording).
●
Once the cassette is ejected, the calibration data is
canceled. The next time the cassette is used for
recording, calibration is re-performed.
●
While Video Calibration is operative, the
PAUSE
button will not function.
●
To display the Video Calibration screen, “SUPERIM-
POSE” must be set to “ON” or the Video Calibration
screen will not appear (
੬
pg. 41).
Playback
The recorder assesses the quality of the tape once you start
playback.
Perform steps 1 – 3 on page 34 (“Simple Playback”) before
continuing.
VIDEO CALIBRATION
START END
ACTIVE VIDEO CALIBRATION
+
+
+
+
DURING CALIBRATION
CALIBRATION COMPLETE
START END
ACTIVE VIDEO CALIBRATION
+
+
+
+
PLAYBACK FEATURES for VHS deck (cont.)
● VHS/S-VHS
To prevent accidental
recording on a
recorded cassette,
remove its safety tab.
To record on it later,
cover the hole with
adhesive tape.
Record safety tab
Accidental erasure prevention
DIGITPURE TECHNOLOGY
HM-HDS1
POWER
S-VHS ET
S-VHS
HDD
OK
MENU
REC LINK
CH
NAVI
STOP PLAY PAUSE REC
REW FEW
A. DUB
EJECT
VIDEO
PAUSE
S-VIDEO
(M) L – AUDIO – R
F - 1
123
4 56
789
0
2
1
4
3
>
<
1
2
–
+
PLAY
PAUSE
PAUSE
REC
PLAY
REC