Filter
Top Products
E-21
Timer and sleep operation (Remote control only)
BLUETOOTH
PAIRING
Timer playback:
The unit turns on and plays the desired source (CD,
TUNER, USB, iPod, AUDIO IN) at a preset time.
This unit has 2 types of timer: ONCE TIMER and DAILY
TIMER.
Once timer (“
” indicator):
Once timer play works for one time only at a preset time.
Daily timer (“DAILY” indicator):
Daily timer play works at the same preset time every day
that we set. For example, set the timer as a wake-up call
every morning.
Using the once timer and daily timer in combination:
For example, use the once timer to listen a radio
programme, and use the daily timer to wake up.
1 Set the daily timer.
2 Set the once timer.
1 minute or more
Daily timer Once timer
Stop StartStart Stop
■ Timer playback
Before setting timer:
● Check that the clock is set to the correct time (refer
to page 7). If it is not set, you cannot use the timer
function.
● For timer playback: Plug in USB or load discs or dock
iPod to be played.
1 Press the ON/STAND-BY button to turn the power on.
2 Press and hold the CLOCK/TIMER button.
3 Within 10 seconds, press the or button to select
“Once” or “Daily”, and press the ENTER button.
4 Within 10 seconds, press the or button to select
“Timer Set”, and press the ENTER button.
5 To select the timer playback source (CD, TUNER, USB,
iPod, AUDIO IN), press the
or button. Press the
ENTER button.
When you select the tuner, select a station by pressing
the
or button, and then press the ENTER button.
If a station has not been programmed, “No Preset” will
be displayed and timer setting will be cancelled.
6 To adjust the day, press the or button and then
press the ENTER button.
7 Press the ENTER button to adjust the hour. Press the
or button and then press the ENTER button.
8 To adjust the minutes, press the or button and
then press the ENTER button.
9 Set the time to finish as in steps 7 and 8 above.
10 Adjust the volume using the VOLUME (+ or -) on the main
unit or VOL +/- on the remote control, and then press the
ENTER button. Do not turn the volume up too high.
11 Press the ON/STAND-BY button to enter the power
stand-by mode. The “TIMER” indicator lights up and
the unit is ready for timer playback.
12 When the preset time is reached, playback will start.
The volume will increase gradually until it reaches the
preset volume. The timer indicator will blink during timer
playback. When the timer end time is reached, the system
will enter the power stand-by mode automatically.
Once timer:
The timer will be cancelled.
Daily timer:
The timer operates at the same time every selected
day. It will continue until the daily timer setting is
cancelled. Cancel the daily timer when it is not in use.
Notes:
● When performing timer playback using another unit
connected to the USB terminal or AUDIO IN socket,
select “USB” or “AUDIO IN” in step 5.
● This unit will turn on or enter the power stand-by
mode automatically. However, the connected unit will
not turn on or off. To stop the timer playback, follow
step “Cancelling the timer setting” of this page.
Checking the timer setting:
1 Turn the power on and press and hold down the
CLOCK/TIMER button.
2 Within 10 seconds, press the or button to select
“Once” or “Daily”, and press the ENTER button.
3 Within 10 seconds, press the or button to select
“Timer Call”, and press the ENTER button.
Cancelling the timer setting:
1 Turn the power on and press and hold down the
CLOCK/TIMER button.
2 Within 10 seconds, press the or button to select
“Once” or “Daily”, and press the ENTER button.
3 Within 10 seconds, press the or button to select
“Timer Off”, and press the ENTER button. Timer will
be cancelled (the setting will not be cancelled).
Reusing the memorised timer setting:
The timer setting will be memorised once it is entered. To
reuse the same setting, perform the following operations.
1 Turn the power on and press and hold down the
CLOCK/TIMER button.
2 Within 10 seconds, press the or button to select
“Once” or “Daily”, and press the ENTER button.
3 Within 10 seconds, press the or button to select
“Timer On” , and press the ENTER button.
4 Press the ON/STAND-BY button to enter the power
stand-by mode.