Filter
Top Products
Internet and PC Link
22 Please visit http://My.Philips.com
English
If ‘Are you using a wireless (WiFi/802.11) or a
wired (Ethernet) network connection?’ appears
● Press the red button (SUBTITLE) on the remote control to
connect to a wireless network.
If ‘Enter wireless network name (SSID)’ appears
1 Press the red button (SUBTITLE) on the remote control to
search again for all available networks or, use the number
buttons to enter the network name (SSID) of your wireless
network.
The network name is case sensitive. Press the number
buttons repeatedly to change from lower to upper case
characters. On the display of the Streamium System case-
sensitive characters are distinguished by size. For example,
“Gg” will be shown as “GG.”
2 Press 2OK to confirm.
➜ Are you using an Access Point or Ad-Hoc
network? appears.
3 Press the red button (SUBTITLE) on the remote control to
select Access Point.
➜ Are you using WEP encryption on your wireless
network? appears.
4 If your network is not WEP encrypted, press the red button
(SUBTITLE) on the remote control to connect to the
Internet.
If the network is WEP encrypted, press the green button
(ANGLE) on the remote control.
If the network is WEP encrypted
You will be asked to enter up to 4 encryption keys. Check
the setup menu of your wireless router to see which
encryption keys are used.
1 Use the number buttons to enter the encryption key. Next,
press 2OK to confirm.
2 Repeat step 1 for all encryption keys. If not all of the
4 encryption keys are used in your network, enter “0”
(zero) for no encryption key.
If the Streamium System does not connect to the
Internet
The Streamium System may not connect to the Internet
because
– a connection error has occurred. Press INTERNET again
to reconnect.
– the wireless router is not connected to the Internet.
Check if the computers in your network have access to
the Internet.
– the IP settings are not correct. Continue with “If ‘An IP
address could not be obtained automatically.Would you
like to enter your network settings manually?’ appears.”
– your Internet service provider is using a proxy. Continue
with “If ‘The system could not connect to the server.’
appears.”
If ‘An IP address could not be obtained
automatically.Would you like to enter your
network settings manually?’ appears
1 Press the red button (SUBTITLE) on the remote control to
connect again to the Internet automatically. Always try this
solution first. If necessary, repeat this step several times.
2 If the Streamium System connects to the Internet, continue
with chapter “Registration.”
If the Streamium System does not connect to the Internet,
press the green button (ANGLE) on the remote control to
enter the IP settings manually. Please contact your Internet
service provider to get all the information you need below.
Next, you will be asked to enter
– the IP address for the Streamium System
– the netmask: Make sure all computers in your network
as well as the Streamium System have the same
netmask. If you are not sure, try 255.255.255.0.
– Default Gateway: the IP address of your router
– two DNS.
Use the number buttons on the remote control to enter
each setting and press 2OK to confirm each setting.
If ‘The system could not connect to the server.’
appears
Maybe the system does not connect to the Internet
because your Internet service provider uses a proxy.You
need to enter the proxy name and proxy port. Please
contact your Internet service provider to get this
information.
1 Press the green button (ANGLE) on the remote control if
your Internet service provider uses a proxy.
2 Use the number buttons to enter the proxy name. Next,
press 2OK.
3 Use the number buttons to enter the proxy port. Next,
press 2OK.
➜ The Streamium System tries to connect to the Internet.
PC LINK connection
● After the Streamium System has connected successfully to
the Internet, press PC LINK to connect to the PCs in your
network.
The Streamium System may not connect to the PC
because
– a connection error has occurred. Press PC LINK again.
– you have not yet installed the Philips Media Manager
software on your PC.
– the PC is switched off.