Filter
Top Products
EN 41
123
456
7
89
0
2
4
1
3
T W
DV S-VHS
PROG.
TIMER
SP/EP
NUMBER "9"
NUMBER "8"
CANCEL
INPUT RECEIVING CHANNEL
NUMBER
5
The Guide Channel
Number, which is assigned
to the TV or cable station
for the PlusCode number
that you entered in step 4,
will appear automatically
on the Guide Channel Set
screen. Input the number
of the channel on which
the broadcast for the PlusCode number is received on
the VCR or cable box using the NUMBER keys, CH +/–
or %fi, then press OK.
● The Guide Channel Set screen appears only when you
input the PlusCode number of a station for which the
Guide Channel number has not previously been set.
● If you receive your channels with a cable box and if
you have properly set your Controller, "CABLE CH"
appears in place of "VCR CH". If not, refer to pages
15 – 17.
CHECK PROGRAM DATA
6
The PlusCode number you
entered and the matching
Timer-Recording informa-
tion is displayed on the
Program screen. Check to
make sure it’s accurate.
● To change the stop time,
press STOP +/–.
● To timer-record daily or weekly serials, press DAILY
(NUMBER key “8”) or WEEKLY (NUMBER key “9”).
“DAILY” or “WEEKLY” appears on the Program
screen. Pressing the button again makes each
corresponding display disappear.
● If you made a mistake, press CANCEL to access the
VCR Plus+ screen again and input the correct
PlusCode number.
● If the PlusCode number you inputted is incorrect,
"ERROR" may appear on the screen to advise you of
the error. This happens when the PlusCode number is
for a program which has already passed. "ERROR" is
displayed for about 5 seconds and the VCR Plus+
screen reappears.
SET TAPE SPEED
7
Press SP/EP (SP/LP for the DV deck).
RETURN TO NORMAL
SCREEN
8
Press PROG. or OK. "PROGRAM COMPLETED"
appears on the screen for about 5 seconds, then normal
screen appears. If "PROGRAM NOT COMPLETED
PROGRAM OVERLAP" appears on the TV screen, see
page 47.
ENGAGE TIMER MODE
9
Press TIMER. The VCR turns off automatically and "‰"
is displayed on the display panel.
IMPORTANT
If you have moved to a different area or if a broadcasting
station's channel number has been changed, the wrong VCR
or CABLE CH number will be displayed on the VCR Plus+
program screen in step 6. When this happens, set the correct
the Guide Channel number for that station. (੬ pg. 42,
"Changing VCR Plus+
®
Setting")
NOTES:
●
To disengage the timer before recording starts, press
TIMER
again. Pressing once more re-engages it.
●
In case of a power failure after programming, the VCR’s
memory backup keeps your selections for approximately
60 minutes.
●
When timer-recording cable channels received through a
Cable Box, be sure to keep the Cable Box set to ON.
●
It is not possible to timer-record the same programme on both
the VHS deck and the DV deck simultaneously.
●
If the times that are programmed for recording on the DV
deck and on the VHS deck overlap, the earlier start time takes
precedence. If the start times are the same, the VHS deck
takes precedence.
STOP+/–
OK
GUIDE CHANNEL SET
GUIDE CH: 12
VCR CH : –––
PRESS NUMBER KEY (0–9)
OR (5,∞), THEN (OK)
PRESS (PROG.) TO END
VHS PROGRAM 1
(VCR PLUS+ 12345678)
START STOP
8:00PM = 10:00PM
DATE CH
12/24/00 12 SP
THU
PRESS (8=DAILY, 9=WEEKLY
STOP+/– = STOP TIME, SP/EP)
PRESS (OK) TO END