Filter
Top Products
(E) Symbio 160HD4
8
Copyright © 2004 TOSHIBA CORPORATION. All rights reserved.
Disconnecting and relocating the
Symbio AVHD recorder
When moving your Symbio AVHD recorder, follow these
procedures to prevent damage to the device’s hard drive.
Note: Never disconnect the power from the AVHD
recorder while it is recording or playing, unless it is an
emergency. Disconnecting the power during operation may cause
malfunction, equipment damage, or data loss. Before disconnecting
the power, stop all AVHD operations and close all AVHD windows on
the TV, and make sure the REC and PLAY LEDs on the AVHD
recorder’s front panel are NOT illuminated.
To shut down and disconnect the Symbio AVHD recorder:
1. Stop all AVHD operations and close all AVHD windows on
the TV.
2. Make sure the REC and PLAY LEDs on the Symbio’s front
panel are NOT illuminated.
3. Turn off the television.
4. Unplug the IEEE-1394 cable from the Symbio AVHD
recorder.
5. Unplug the Symbio AVHD recorder’s power cord from the
AC outlet.
6. Wait at least 15 seconds before relocating the Symbio
AVHD recorder to ensure that the Symbio’s hard drive
has stopped spinning.
Note: The top of the Symbio AVHD recorder can become hot
during operation. This is normal. Wear protective gloves while
handling it or allow the device to cool before handling it.
7. Carefully move the Symbio AVHD recorder to its new
location.
Note: Never subject the Symbio AVHD recorder to extreme
temperatures or jolting impact when moving the device.
To reconnect the Symbio AVHD recorder:
1. Plug the Symbio AVHD recorder’s power cord back in to
the AC outlet.
2. Plug the IEEE-1394 cable from the television back in to the
Symbio AVHD recorder.
Note: If the POWER LED on the front of the Symbio device
does not illuminate after plugging in the power cord, check all
cable connections and power sources.
3. Turn on the television.
4.
Wait at least 30 seconds before using the Symbio AVHD
recorder
.
Connecting the Symbio AVHD
recorder
The back of the Symbio AVHD recorder has two 6-pin
DTVLink/IEEE-1394 ports and one A/C power cord
connector. IEEE-1394 devices (such as your Toshiba integrated
HD television) can be connected to either DTVLink port on
the Symbio. Devices must be DTVLink-certified to send/receive
encrypted content.
To connect the Symbio AVHD recorder to the Toshiba
integrated HD television:
1. Connect the AC power cord to the back of the Symbio
AVHD recorder, and then plug the other end into an
AC outlet or surge protector.
2. Connect the smaller 4-pin end of the IEEE-1394 cable to
one of the IEEE-1394 (TheaterNet) ports on the Toshiba
integrated HD television.
3. Connect the larger 6-pin end of the IEEE-1394 cable to
either IEEE-1394 port on the Symbio AVHD recorder.
4. Turn on the television.
5.
Wait several minutes before using the Symbio AVHD
recorder
. If your Symbio AVHD recorder contains many
recordings, it can take several minutes before it is fully
initialized.
6. See Chapters 3 and 4 of this manual for details on
configuring and using your Symbio AVHD recorder.
Back of Symbio AVHD recorder
(The IEEE-1394 ports on the Symbio
AVHD recorder are labeled “DTVLink.”)
Back panel of Toshiba integrated HD television
(example only; may not represent your specific TV model)
Chapter 2: Connecting the Symbio AVHD recorder
Symbio(E)06_A_06-24 10/19/04, 3:01 PM8