Sharp MD X5 Clock Radio User Manual


 
2
Note:
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interfer-
ence to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
I Reorient or relocate the receiving antenna.
I Increase the separation between the equipment and receiver.
I Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
I Consult the dealer or an experienced radio/TV technician for help.
WARNING
FCC Regulations state that any unauthorized changes or modifications to
this equipment not expressly approved by the manufacturer could void the
user’s authority to operate this equipment.
SPECIAL NOTES FOR FCC COMPOSITE DEVICE:
This device is a composite system. The digital device component may not
cause harmful interference.
I It is the intent of Sharp that this product be used in full compliance with
the copyright laws of the United States and that prior permission be
obtined from copyright owners whenever necessary.
(Continued)
Caution - use of controls or adjustments or
performance of procedures other than those
specified herein may result in hazardous radiation
exposure.
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
0001
PRECAUTIONS
0002
HH
HH
H General
I Do not use oil, solvents, gasoline, paint thinner or insecticides on
the unit.
I Do not expose the unit to moisture, to temperatures higher than
140°F (60°C) or to extreme low temperatures.
I Keep the unit away from direct sunlight, strong magnetic fields,
excessive dust, humidity and electronic/electrical equipment (home
computers, facsimiles, etc.) which generates electrical noise.
I Hold the AC power plug by the head when removing it from the AC
outlet, since pulling the cord can damage internal wires.
I Use the unit on a firm, level surface free from vibration.
I If the unit does not work properly while in use, press the POWER
button to turn the power off, then disconnect the AC power cord from
the AC outlet. Plug the AC power cord back in, and then press the
POWER button to turn the power on.
I If an electrical storm is taking place near you, it is suggested that
you disconnect the AC power cord from the AC outlet for safety.
I Before moving the unit, be sure to remove all CDs and MDs from the
unit. Then, turn the power off and unplug the AC power cord.
If you move the unit with CDs or MDs left in it, they may jam inside
the unit, leading to damage.
Warning:
The voltage used must be the same as that specified on this unit. Using
this product with a higher voltage than that which is specified is
dangerous and may result in a fire or other type of accident causing
damage. SHARP will not be held responsible for any damage resulting
from use of this unit with a voltage other than that which is specified.
HH
HH
H Volume control
The sound level at a given volume setting depends on a combination
of speaker efficiency, location and many other factors.
It is advisable to avoid exposure to high volume levels, which occur
while turning the unit on with the volume control setting up high, or while
continually listening at high volumes.
HH
HH
H Condensation
Sudden temperature changes and storage or operation in an extremely
humid environment may cause condensation inside the cabinet.
Condensation can cause the unit to malfunction.
Follow the procedure below to eliminate condensation.
II
II
I CD and MD pickups
Leave the power on with no disc in the unit until normal playback is possible
(about 1 hour).
II
II
I Remote control
Wipe off any condensation on the transmitter LED with a soft cloth before
operating the unit.
HH
HH
H Care of compact discs
Compact discs are fairly resistant to damage, however mistracking can
occur due to an accumulation of dirt on the disc surface.
Follow the guidelines below for maximum enjoyment from your CD collec-
tion and player.
I Do not write on either side of the disc, particularly the non-label side.
Signals are read from the non-label side. Do not mark on this surface.
I Keep your discs away from direct sunlight, heat, and excessive mois-
ture.
I Always hold CDs by the edges. Fingerprints, dirt, or water on the CDs
can cause noise or mistracking. If a CD is dirty or does not play properly,
clean it with a soft, dry cloth, wiping straight out from the center, along
the radius.
US and foreign patents licensed from Dolby Laboratories Licensing Corpo-
ration.
*01-21 98.6.23, 10:09 AM2