Filter
Top Products
PROGRAM
15
You can select tracks and store them either in the CD changer
or CD recorder memory. If you use the program for playback
you can choose one of the two memories, else if you like to
specify tracks for recording, use the CD changer memory only!
You can store any track more than once.
1 Load the desired disc(s) in the disc tray(s).
2 Press either CD 1, CD 2, CD 3, or CDR to select the disc.
3 Press PROG on the set (PROGRAM on the remote control).
yPROG starts blinking and Program is displayed.
4 If either CD 1, CD 2 or CD 3 is selected:
Rotate JOG CONTROL to select either:
yCD1 (or 2, 3) All: All tracks of CD 1 (or 2, 3) will be
programmed.
yCD1 (or 2, 3) and track number: The track number of
CD 1 (or 2, 3) will be programmed.
If CDR is selected:
Rotate JOG CONTROL (press the numerical keys on the
remote control; for 2-digit numbers, press the keys in rapid
succession) to select a track number.
5 Press YES to store your selection in the memory.
yThe number of programmed tracks (STEP), Prog and the
total program time are displayed. The track number
blinks in the music calendar.
6 Select and store all desired tracks in this way.
7 Press PROG on the set (PROGRAM on the remote control) to
end programming.
yPROG stays shown and the program is currently available.
Note: If the maximum number of programmable tracks is
reached, the display shows Program full.
1 If necessary press STOP & on the set (Ç on the remote
control) to stop playback.
2 Press either CD 1, CD 2, CD 3, or CDR to select the desired
memory.
3 Press PROG (PROGRAM on the remote control), followed by
! SEARCH or ⁄ SEARCH (à or á on the remote
control) to move through the program steps.
yThe track number at the selected step and the total
program time are displayed.
4 Press NO to remove the track from the program.
yCleared is displayed briefly.
yThe next programmed track number will move up to this
position and is displayed together with the step number
and the remaining total program time.
1 If necessary press STOP & on the set (Ç on the remote
control) to stop playback.
2 Press NO.
yClear Prog? is displayed.
3 Press YES to clear the program.
yProg Cleared will be displayed and PROG goes off.
Note: When you open the CD recorder tray or the CD changer
tray the respective program will be cleared.
1 Select and store all desired tracks in the CD changer
memory (see “Programming track numbers”).
2 Enter the recording menu (see “Internal recording”).
• If the total time of the program is of bigger size than the
remaining recording time of the CDR(W):
yNot fitting! will be displayed briefly, followed by
the remaining recording time and Record Prog?
If you nevertheless start recording, only those tracks of the
program that fit onto the CDR(W) will be recorded in entirety.
•To change the program press NO.
yEdit Program will be displayed briefly, PROG and
the time of the program start blinking. Now you can
change the program (see “Programming track numbers”,
“Erasing a track from the program” and “Clearing the
program”).
Making a program for recording
Clearing the program
Erasing a track from the program
Programming track numbers
English
J
O
G
C
O
N
T
R
O
L
TRACK
T
EX
T
R
E
C
L
E
V
E
L
S
E
A
R
C
H
E
D
I
T
P
R
O
G
S
E
A
R
C
H
FINALIZE
ERASE
R
E
C
T
Y
P
E
CD
CD
COMPILE
CD
RECORD
M
A
S
T
E
R
V
O
L
U
M
E
P
U
R
E
L
O
U
D
N
E
S
S
I
N
C
R
E
D
I
B
L
E
P
L
AY
/
P
A
U
S
E
S
T
O
P
N
O
Y
E
S