Filter
Top Products
34
77
77
7 Unfinalizing a disc—only for CD-RW
By erasing the TOC (Table of Contents) of a finalized CD-RW,
you will be able to record on the CD-RW again.
This erasing process of the TOC is called “Unfinalization.”
• Unfinalization is just to erase the TOC, but not the recorded
music signals on the disc.
IMPORTANT
When you unplug the power cord or when a power failure
occurs while “UNFINALIZE” is flashing on the display, the
disc may not be utilized any more.
1
Load a finalized disc you want to unfinalize on
the CD Recorder disc tray.
The CD-RW and FINALIZED indicators light up on the display.
2
While 3-CD Changer and CD Recorder are in stop
mode, press MENU.
3
Turn MULTI JOG ¢ / 4 on the unit or press 3
or 2 on the remote control until “UNFINALIZE”
appears on the display then press SET.
“UNFINALIZE?” appears on the display.
• If an unfinalized disc is loaded, “ALREADY UNFIN”
appears on the display.
4
Press SET to unfinalize the disc.
Unfinalization starts. The REC indicator lights up and the
3 indicator and “UNFINALIZE” start flashing on the
display.
• Unfinalization requires a few minutes to complete.
(When the disc is unfinalized, the REC indicator goes
off and the 3 indicator and “UNFINALIZE” stop flashing
then go off.)
To cancel the unfinalization, press CANCEL in step 3.
COMPACT
DIGITAL AUDIO
Recordable
ReWritable
COMPACT
DIGITAL AUDIO
XL – R5020 CD/CDR MULTIPLE COMPACT DISC RECORDER
On the unit: Remote control:
C
A
N
C
E
L
R
E
C
S
O
U
R
C
E
D
I
S
P
L
A
Y
M
E
N
U
1
PLAY
CD REC CD EDIT SYNCHRO FADE
REC
PITCH 0
FINALIZE
MODE
SET
GROUP
REPEAT CD CDR
4
7
10
2
5
8
3
6
9
10
GROUP
CONTROL
GROUP
CANCEL
CANCEL
77
77
7 Recording track marks manually
When auto track-marking is activated (initial setting), track
marks are recorded automatically. To cancel auto track- marking
and use manual track marking, follow the procedure below.
1
While 3-CD Changer and CD Recorder are in stop
mode, press MENU.
2
Turn MULTI JOG ¢ / 4 on the unit or press 3
or 2 on the remote control until “AUTO TRACK”
appears on the display then press SET.
“AUTO TR ON” (initial setting) appears on the display.
• To cancel the setting, press CANCEL.
3
Turn MULTI JOG ¢ / 4 on the unit or press 3
or 2 on the remote control to select “AUTO TR
OFF,” then press SET.
The AUTO TRACK indicator goes off from the display, and
auto track-marking is canceled. Now you can put track
marks manually during recording.
To put track marks during recording manually, press SET
at the point where you want to put a track mark. You can
add up to 99 track marks.
SET
MULTI JOG
¢ / 4
MENU
MENU
SET
3 / 2
77
77
7 Recording only one track from an external
component
Digital recording from an MD recorder, a CD player, or a DAT
deck connected to the DIGITAL IN terminals is initially set to
record entire disc. You can also use Synchronized Recording
for recording only one track. To use Synchronized Recording
for one track, follow the procedure below.
Available source
OPTICAL IN, COAXIAL IN
1
While 3-CD Changer and CD Recorder are in
stop mode, press MENU.
2
Turn MULTI JOG ¢ / 4 on the unit or press 3
or 2 on the remote control until “DIG-IN SYNC”
appears on the display, then press SET.
“SYNC ALL” (initial setting) appears on the display.
• To cancel the setting, press CANCEL.
3
Turn MULTI JOG ¢ / 4 on the unit or press 3
or 2 on the remote control to select “SYNC 1-
TRACK” then press SET.
To use Synchronized Recording for recording all tracks,
select “SYNC ALL” in step 3.
Digital signal cannot be output through the DIGITAL OUT terminals
while recording digitally from an external component.
CD Recorder
disc tray