A SERVICE OF

logo

Open as PDF
next previous
9696 97
Return to the Top page
Audio Setting Up
Return to the Top page
Audio Setting Up
Crossover network setup
Youcansetacrossoverfrequencyof
speakers.
1 Touch the speaker to set the crossover
in the Speaker Select screen.
2 Touch [X’over].
X’over screen appears.
3 Set each item as follows.
TW (Tweeter) Gain *
1
Adjuststhetweeterlevel.(Whenfrontis
selectedonSpeakerSelectscreen)
Gain
Adjuststhefrontspeaker,rearspeaker,or
subwooferlevel.
Phase*
2
Setsthephaseofsubwooferoutput.
Thephaseisreversed180degreeswhenset
to“Reverse”.(Whensubwooferisselectedon
SpeakerSelectscreen)
HPF FREQ
HighPassFilteradjustment.(Whenfrontorrear
speakerisselectedonSpeakerSelectscreen)
LPF FREQ
LowPassFilteradjustment.(Whensubwoofer
isselectedonSpeakerSelectscreen)
Slope*
3
Setsacrossoverslope.
*
1
Onlywhen“Tweeter”issetto“Small”,
“Middle”,“Large”in<SpeakerSetup>.
*
2
Onlywhen“Subwoofer”issettoamode
otherthan“None”in<SpeakerSetup>.
*
3
Onlywhen“LPFFREQ”/“HPFFREQ”issetto
amodeotherthan“Through”in<X’over>.
WhenSpeakernetworkissetto3way:
Region code 3 area
Range switching area (graph)
Selectsthebandforsettinggain,frequency
filter,andslope.
TouchtheleftarctosettheLPF,thecenterarc
tosettheBPF,andtherightarctosettheHPF.
Phase*
Setsthephaseoftweeter,midrange,and
wooferoutput.
Thephaseisreversed180degreeswhensetto
“Reverse”.
Gain
Setsgainofeachspeaker.
HPF FREQ
HighPassFilteradjustment.(Whentweeteris
selectedonSpeakerSelectscreen)
BPF FREQ
BandPassFilteradjustment.(Whenmidrange
speakerisselectedonSpeakerSelectscreen)
LPF FREQ
LowPassFilteradjustment.(Whenwooferis
selectedonSpeakerSelectscreen)
Slope
Setsacrossoverslope.
NOTE
•Forhowtoswitchtothe3-wayspeakersystem,
see
3 way speaker system setup (P.35)
intheQuickStartGuide.Connecting3-way
speakerswiththe2-waymodeselectedcanbreak
thespeakers.
Car type setup
Youcansetupthecartypeandspeaker
network,etc.
1 Touch [Car Type] in the Audio SETUP
screen.
Car Type screen appears.
2 Select your car type from the list.
NOTE
•Ifyourcartypeisselected,theDelayTime
Alignmentissetautomatically(fortiming
adjustmentofsoundoutputforeachchannel)to
havethehighestsurroundeffects.
Speaker location setup
1 In the Car Type screen, touch [Location].
Speaker Location screen appears.
2 Select the speaker locations using [3].
Front Speaker
Selectthelocationfrom“Door”/“OnDash”/
“UnderDash”.
Rear Speaker
Selectthelocationfrom“Door”/“RearDeck”,
“2ndRow”/“3rdRow”(Minivan,Minivan
(Long)).
WhenSpeakernetworkissetto3way.
Region code 3 area
Mid Range
Selectthelocationfrom“Door”/“OnDash”/
“UnderDash”.