Filter
Top Products
22
<DRB1349>
EFFECT FUNCTIONS
Using the Effect Functions
The basic procedures is as follows: [Select effect type] =
[Set parameters (while monitoring through headphones]
=[Set EFFECT switch to ON].
Below are examples of this basic operation procedure; other
effects are produced in much the same way:
[Example 1] Apply delay to CH-1 track:
1. Touch the touch panel’s CH-1 (left side) DELAY
button (select effect type).
• If the DELAY button is not displayed, select and display
the button as follows:
1Hold the CH-1 (left side) FADER CURVE/BANK EDIT
button depressed for about 1 second to set the touch
panel to the effect select menu.
2Of the touch panel’s three buttons, select (touch) the
one in which you wish to record the DELAY.
3Rotate the TIME/SELECT dial to select DELAY.
4Press (touch) the MEMORY button.
5Press the FADER CURVE/BANK EDIT button to leave
the effect select menu.
• If DELAY is preset in the BANK 1, 2, or 3 buttons,
DELAY can be selected by pressing the corresponding
button (see page 23 “Presetting Effects.”)
2. Press the CH-1 (left side) FX ADJ. button to
display the effect parameter adjust menu on the
touch panel.
3. Use the touch panel’s LOW, MID, and HI buttons
to select the frequency ranges for the effect.
• The selected range button will appear highlighted.
* It may not be possible to select the frequency range,
depending on the type of effect.
4. Press the touch panel’s 1/8 to 8/1 buttons as
desired to select the delay time (parameter value
setting).
• Set delay time of 1/8 to 8/1 for each beat of BPM.
• Set monitor SELECT switch to [EFFECT] to confirm the
effect sound through the headphones (effects marked
with the note *1 on the effects chart cannot be heard
unless the EFFECT switch is set to [ON]).
• The TIME/SELECT dial can be rotated to produce even
finer delay time settings. Setting delay time of 1/2 per
beat of tempo (BPM) will cause the touch panel’s 1/2
button to be highlighted, and this can be used as a
general reference when adjusting the parameter.
5. Use the MIX/DEPTH dial to set the level balance
between sound source and delay sound.
• Rotate to left to reduce, and rotate to right to increase
the delay sound.
6. Set EFFECT switch to [ON] or [LOCK ON].
• The EFFECT indicator will begin flashing red, and the
effect (delay) will be applied to the master output.
• When the EFFECT switch is set to [ON] by pulling the
switch forward, the switch will automatically return to
[OFF] when released.
Note:
• Select effects only when the EFFECT switch is in the [OFF]
position. If effects are selected when the EFFECT switch is in
the [LOCK ON] position, noise may be produced.
[Example 2] Apply fader roll to CH-1 track
1. Touch the touch panel’s CH-1 (left side) FADER
ROLL button (select effect type).
• If the FADER ROLL button is not displayed, select and
display the button as follows:
1Hold the CH-1 (left side) FADER CURVE/BANK EDIT
button depressed for about 1 second to set the touch
panel to the effect select menu.
2Of the touch panel’s three buttons, select (touch) the
one in which you wish to record the FADER ROLL.
3Rotate the TIME/SELECT dial to select FADER ROLL.
4Press (touch) the MEMORY button.
5Press the FADER CURVE/BANK EDIT button to leave
the effect select menu.
• If FADER ROLL is preset in the BANK 1, 2, or 3 buttons,
FADER ROLL can be selected by pressing the
corresponding button (see page 23 “Presetting
Effects.”)
2. Press the CH-1 (left side) FX ADJ. button to
diplay the effect parameter adjust menu on the
touch panel.
3. Use the touch panel’s LOW, MID, and HI buttons
to select the frequency ranges for the effect.
• The selected range button will appear highlighted.
* It may not be possible to select the frequency range,
depending on the type of effect.
4. Press the touch panel’s 1/2, 1/1, and 2/1 buttons
as desired to select the roll time (parameter
value setting).
• Standard roll times can be set as 1/2, 1/1, or 2/1.
• Set monitor SELECT switch to [EFFECT] to confirm the
effect sound through the headphones (effects marked
with the note *1 on the effects chart cannot be heard
unless the EFFECT switch is set to [ON]).
• The TIME/SELECT dial can be rotated to produce even
finer roll time settings. Setting roll time to 1/1 per beat
of tempo (BPM) will cause the touch panel’s 1/1 button
to be highlighted, and this can be used as a general
reference when adjusting the parameter.
5. Use the MIX/DEPTH dial to set the roll sound
level.
• Rotate to left to reduce, and rotate to right to increase
the roll sound.
6. Use touch panel’s CROSS FADER button to
select fader.
• The fader used for fader effects can be set to either
channel fader or cross fader.
7. Set EFFECT switch to [ON] or [LOCK ON].
• The EFFECT indicator will begin flashing red, and the
effect will be applied to the master output.
• When the EFFECT switch is set to [ON] by pulling the
switch forward, the switch will automatically return to
[OFF] when released.
Note:
• Make selection of effects and type of fader (channel or cross)
only when the EFFECT switch is in the [OFF] position. If
effects are selected when the EFFECT switch is in the [LOCK
ON] position, noise may be produced.