Filter
Top Products
E-8
7. When the alarm source is successfully understood, the unit will reply, “Please say the time you would
like the alarm to sound, including AM or PM” while the current alarm time is displayed.
8. Say the time you wish Alarm One to sound in a clear, normal voice without any pause between words.
Example: to set Alarm One to 10:19AM, say “Ten Nineteen AM”.
9. When the alarm one time is successfully understood, the unit will reply “Alarm One is now set to …”
and repeat the time you gave. Example: if you said to set the alarm time to 10:19AM, the reply will be
“Alarm One is now set to ten-nineteen AM”. The Alarm One indicator on the display (#25) will now light.
10. If the unit fails to understand the alarm time given, it will reply, “I’m sorry, I didn’t get that. Please tell
me the time you would like the alarm to set, for example, eight-thirty AM”. Now repeat step #8
above.
11. If the unit fails to understand the alarm time given a second time, it will reply “I’m sorry. I did not
understand you, please start over or set the alarm time manually”. If this occurs, repeat steps #1 –
4 and 8 above again making sure you speak clearly in a normal voice and avoid pauses between words.
12. To set Alarm Two, repeat steps #1 - 4 above and say “Alarm Two” when prompted (step #4). The
Alarm Two indicator on the display (#26) will light once complete.
TO SET THE ALARM WAKE SOUNDS (AL1/AL2)
1. Start by saying the trigger word “Hello Clock Radio” or press the SNOOZE BAR (#11).
2. The unit will reply “Yes” and will wait for your next command.
3. Say “Alarm Sound” and the unit will reply “To set alarm sound, please say Alarm One or Alarm
Two”.
4. To set Alarm One, say “Alarm One”. You can also say the command “Cancel” during this step if you
wish to cancel setting the alarm sound.
5. If the unit fails to understand the alarm source given, it will reply, “Please Repeat”. Now repeat step
#4 above.
6. If the unit fails to understand the alarm source given a second time, it will reply “I’m sorry. I did not
understand you, please start over or set the alarm sound manually”. If this occurs, repeat steps
#1 - 4 above again making sure you speak clearly in a normal voice.
7. When the alarm source is successfully understood, the unit will reply, “To choose an alarm sound,
say Ocean, Rain, Brook, Radio or Beep”.
8. Say Ocean, Rain, Brook, Radio or Beep. You can also say the command “Cancel” during this step if
you wish to cancel setting the alarm sound and the unit will reply “OK” to confirm.
9. When the alarm sound is successfully understood, the unit will reply “Alarm One sound is set to…”
and repeat the alarm sound you have chosen. The alarm one sound selected will light in the display
(#25).
10. If the unit fails to understand the alarm sound given for the first and second times, it will reply “Please
Repeat”. Now repeat step #8 above.
11. If the unit fails to understand the alarm sound given a third time, it will reply “I’m sorry. I did not
understand you, please start over or set the alarm sound manually”.
12. To set Alarm Two Sound, repeat steps #1 – 4 and 8 above and say “Alarm Two” when prompted
(step #4). The alarm two sound selected will light in the display (#26) when completed.
NOTE:
- When the preset alarm time is reached, the chosen alarm sound will start sounding at a fairly low
volume level and gradually increase to a very loud volume level in 60 seconds. It will last for 60 minutes
if uninterrupted.
- When the alarm is sounding, there will be a periodic pause in the alarm sound if you chose a nature
sound (Ocean, Rain or Brook) or the Beep for your wake alarm. This is normal and the point where the
unit is listening for one of the two Talk ’N Set commands (“Snooze” or “Alarm Off”).
- If radio is chosen as the alarm sound, you will not be able to use Talk ’N Set commands to activate
snooze or turn the alarm off. This will need to be done manually by pressing either AL1 ON/OFF (#2),
AL2 ON/OFF (#8) or ON/FF (#12) BUTTON.
- If the latter alarm time is reached before the first sounding alarm has ended, the first alarm will be
instantly overridden and the new alarm session will sound for 60 minutes if uninterrupted.
- An active alarm will always sound no matter the unit is off, in sleep mode or playing through a
radio/external MP3 player.
- If you choose the radio alarm but an external audio device remains to be connected to the LINE IN
JACK (#18) by a stereo cord (not included) when the alarm time is reached, the beep alarm will
automatically switch in to substitute the radio alarm.
TO CHECK THE ALARM TIME (AL1/AL2)