E-10
2. If you do not wish the alarm to sound again, you can disable it by pressing either the AL1 ON/OFF
BUTTON (#2) or AL2 ON/OFF BUTTON (#8). The corresponding alarm indicators on the display (#25 &
#26) will go off.
3. To enable the alarms again, press either the AL1 ON/OFF BUTTON (#2) or AL2 ON/OFF BUTTON (#8).
The corresponding alarm indicators on the display (#25 & #26) will turn on.
USING TALK ’N SET
1. When the designated alarm time is reached, there will be a periodic pause in the alarm sound if you
chose a nature sound (Ocean, Rain or Brook) or the Beep for your wake alarm. This is normal and
during the pause is where the unit is listening for the “Alarm Off” command.
2. Say “Alarm Off” during one of the pauses in the alarm sound to turn the Alarm off for the day. If the
“Alarm Off” command is correctly recognized, the unit will reply “Yes” and the alarm sound will stop.
The alarm will sound again the next day at the same preset time.
3. If radio is chosen as the alarm sound, it will play without interruption and therefore you will not be able
to use Talk ’N Set “Alarm Off” command to turn it off. The radio alarm will have to be turned off by
pressing either AL1 ON/OFF (#2), AL2 ON/OFF (#8) or ON/FF (#12) BUTTON.
4. Follow the steps in the above Talk ’N Set section “TO CHECK THE ALARM TIME (AL1/AL2)” to turn
the specific alarm off with voice commands if it is initially on. The corresponding alarm indicator on the
display (#25 and/or #26) will turn off to confirm.
SETTING UP THE SLEEP SOUND AND TIME
You can choose either a nature sound (Ocean, Rain or Brook) or the radio as a sleep sound.
The sleep time can be adjusted from: 15, 30, 45 or 60 minutes and OFF.
MANUAL SETTING
SETTING THE SLEEP SOUND
1. The Sleep Sound can be set by repeatedly pressing the SET BUTTON until you get to the to Sleep
Sound settings.
2. Use the > (UP) (#6) or < (DOWN) (#4) BUTTONS to choose a Sleep Sound (Ocean, Rain, Brook or
Radio).
3. The display will show the chosen Sleep sound (#27).
ACTIVATE SLEEP MODE AND SETTING SLEEP TIME
1. Press the SLEEP BUTTON (#10) to start the sleep mode.
2. The default Sleep Time is 60 minutes and “60” will show on the display (#24).
3. Press the SLEEP BUTTON (#10) repeatedly to cycle through shorter sleep time options of 45, 30, 15
minutes or OFF.
USING TALK ’N SET
SETTING THE SLEEP SOUND, TIME AND STARTING THE SLEEP FUNCTION
1. Start by saying the trigger word “Hello Clock Radio” or press the Snooze Bar (#11).
2. The unit will reply “Yes” and will wait for your next command.
3. Say “Play Sleep Sound” and the unit will reply “To Choose a Sleep Sound, Say Ocean, Rain,
Brook or Radio”.
4. Say “Ocean”, “Rain”, “Brook” or “Radio”. You can also say the command “Cancel” during this step
if you wish to cancel setting the sleep sound and the unit will reply “OK” to confirm.
5. The unit will now say “Please choose a Sleep Time, say Fifteen, Thirty, Forty-Five or Sixty
Minutes”.
6. Say “Fifteen”, “Thirty”, “Forty-Five” or “Sixty”. You can also cancel the Sleep time by saying the
command “Cancel”. The unit will reply “OK” to confirm.
7. When the sleep time is successfully understood, the unit will say “The Sleep Sound will turn off in …
Minutes”. The number you chose in step #6 will be said.
8. The sleep time chosen will also show on the display (#24).
9. When the sleep sound and time settings are successfully understood, the chosen sleep sound will show
on the display (#27) and be played for the selected sleep time.
10. If the unit fails to understand the sleep time given, it will reply “Please Repeat”. Now repeat step #6
above.
NOTE:
- During sleep, you may press the SLEEP BUTTON (#10) to check the remaining sleep time.