Filter
Top Products
E-7
Time
To check the current time.
* Factory preset time is 12:00AM.
Set Time
To set the current time in AM or PM.
Alarm
To check the alarm time and status of AL1 & AL2. If the alarm is currently off,
you have the option to turn it on or vice versa.
* Factory preset alarm time is 7:00AM for AL1 and 8:00AM for AL2.
Set Alarm
To set the alarm time of AL1 & AL2 in AM or PM.
Alarm Sound
To set the alarm sound for AL1 & AL2. You can select from among 3 nature
sounds (Ocean, Rain or Brook), radio or the beep alarm.
* Factory preset alarm sound is beep alarm for both AL1 & AL2.
Alarm Off
To cancel current alarm for the day while alarming is sounding or clock is in
snooze mode.
Snooze
To activate the 9 minute Snooze while an alarm is sounding. You must say the
command word “Snooze” during the brief pause during the alarm (except radio
mode in which you need to tap the SNOOZE BAR) for it to work correctly.
Play Sleep Sound
To choose a sleep sound from among 3 nature sounds (Ocean, Rain or Brook),
or radio and then to set sleep time for 15, 30, 45 or 60 minutes or to turn it off.
The sleep time is default to 60 minutes. You can adjust sleep sound output
between levels 1-4 by pressing the > (UP) (#6) or < (DOWN) (#4) BUTTONS.
* Factory preset sleep sound is Ocean and its output level is “2”.
Display
To set the LCD backlight brightness to HI or LO.
* Factory preset LCD brightness is “High”.
Cancel
To terminate the Talk ’N Set function immediately after it is activated.
It can also be used in the middle to terminate certain Talk ’N Set commands: Set
Alarm, Alarm Sound, Play Sleep Sound and Display.
CURRENT TIME SETTING AND REPORTING
TO SET THE CURRENT TIME
1. Start by saying the trigger word “Hello Clock Radio” or press the SNOOZE BAR (#11).
2. The unit will reply “Yes” and will wait for your next command.
3. Say “Set Time” and the unit will reply “Tell me the current time including AM or PM”.
4. Say the current time you wish to set the clock to. Example: to set the clock to 3:23AM, say “Three
Twenty Three AM”.
5. When the time is successfully understood, the unit will reply, “The time is …” and repeat the time you
gave. Example: if you said to set the time to 3:23AM, the reply will be “The time is three-twenty- three
AM”.
6. If the unit fails to understand the time given, it will reply, “I’m sorry. I didn’t get that. Please tell me
the current time, for example, seven-thirty-five PM”. Now repeat step #4 above.
7. If the unit fails to understand the time given a second time, it will reply, “I’m sorry. I did not
understand you, please start over or set the time manually”. If this occurs, repeat steps #1 - 4
above again making sure you speak clearly in a normal voice and avoid pauses between words.
TO CHECK THE CURRENT TIME
1. Start by saying the trigger word “Hello Clock Radio” or press the SNOOZE BAR (#11).
2. The unit will reply “Yes” and will wait for your next command.
3. Say “Time” and the unit will reply “The time is ...” followed by the present time.
ALARM TIME AND ALARM SOUND SETTING / CHECKING
TO SET THE ALARM TIME (AL1/AL2)
1. Start by saying the trigger word “Hello Clock Radio” or press the SNOOZE BAR (#11).
2. The unit will reply “Yes” and will wait for your next command.
3. Say “Set Alarm” and the unit will reply “Say Alarm One or Alarm Two”.
4. To set Alarm One, say “Alarm One”. You can also say the command “Cancel” during this step if you
wish to cancel setting the alarm and the unit will reply “OK” to confirm..
5. If the unit fails to understand the alarm source given, it will reply, “Please Repeat”. Now repeat step
#4 above.
6. If the unit fails to understand the alarm source given a second time, it will reply “I’m sorry. I did not
understand you, please start over or set the alarm time manually”. If this occurs, repeat steps #1 -
4 above again making sure you speak clearly in a normal voice.