Pioneer DVR-531H-S MP3 Player User Manual


 
Recording
06
54
En
Important
The source signal must be DVC-SD format
Some camcorders cannot be controlled using this
recorder’s remote.
If you connect a second recorder using a DV cable,
you cannot control the second unit from this one.
You can’t control this unit remotely from a
component connected to the
DV IN
jack.
You can’t record date and time information from DV
cassette.
During DV recording, if a part of the tape is blank, or
has copy-protected material on it, this recorder will
pause recording. Recording will restart automatically
when there is a recordable signal. However, if there is
more than 10 seconds of blank tape, this recorder will
stop recording and the camcorder should stop
(depending on the camcorder).
For best results when recording from a DV
camcorder to this recorder, we recommend cueing
the camcorder to the place you want to start
recording from and setting the camcorder to play-
pause.
1 Make sure your digital camcorder is connected to
the front panel DV IN jack.
Also, set the camcorder to VTR mode.
2 Set up the recorder.
Use
REC MODE
to set the recording quality. See
Setting the picture quality/recording time
on page 51
for detailed information.
Make sure a recordable disc is loaded if you want to
record to DVD.
3 From the Initial Settings menu, check that the DV
audio input is setup as you require.
See
DV Input
on page 93 for more on this.
Check also that the
Audio In
settings for
External
Audio
and
Dual Mono Recording
are as you want
them (see
Audio In Settings
on page 93).
4 Press HOME MENU, select ‘Copy’, then ‘DV
Record’ from the menu.
DV recording only works when the digital camcorder
is in VTR mode with a tape loaded.
5 Select ‘Record to Hard Disk Drive’ or ‘Record to
DVD’ to record to the hard disk drive or a recordable
DVD respectively.
6 Find the place on the camcorder tape that you
want to start recording from.
For best results, pause playback at the point from which
you want to record.
Depending on your camcorder, you can use this
recorder’s remote to control the camcorder using the
,
,
,
,
,
and
buttons.
7 Use the
/
buttons to select ‘Start Rec’ and
press ENTER.
Recording is automatically paused if the recorder
detects no signal, or a copy-protected signal.
Recording restarts when there is a non-copy-
protected signal.
You can pause or stop the recording by selecting
Pause Rec
or
Stop Rec
from the on-screen display.
You cannot control the camcorder from this remote
control during recording.
If you restart recording after stopping the camcorder,
the first few seconds of the camcorder tape will not
be recorded. Use the pause button on your
camcorder instead and recording will start
immediately.
HDD and DVD-RW (VR Mode) only:
A chapter marker
is inserted every time there is a break in the timecode
on the DV tape. This happens when the recording is
stopped or paused then restarted, for example.
While recording, you cannot exit the DV recording
screen using the
HOME MENU
or
RETURN
button.
See also
DV-related messages
on page 104 if you
encounter an error while using the
DV IN
jack.
Frequently Asked Questions
•I can’t get my DV camcorder to work with the recorder!
Check that the DV cable is properly connected. Also
make sure that what you’re trying to record is not
copy-protected.
If it still doesn’t work, try switching off the camcorder
then switch back on.
There’s a picture, but no sound!
Try switching the
DV Input
setting (see
DV Input
on
page 93) between
Stereo 1
and
Stereo 2
.
1
Note
1.If the audio subcode on the DV tape cannot be read correctly, the audio type will not switch automatically. You can switch the audio manually
from the
External Audio
setting (page 93).
Start Rec
Pause Rec
Stop Rec
SP (2h00m/DVD)
32h45m
Stop Stop
1.02.22
Control with these
buttons

Rem.
HDD
DVR-530H_KU.book 54 ページ 2005年6月8日 水曜日 午前11時16分