Filter
Top Products
GB
P.10
GB
P. 1 1
Canada City Listing
Code City Code City Code City
EDM Edmonton YEL Yellowknife CHT Charlotte Town
ALB Calgary OTT Ottawa MON Montreal
VAN Vancouver SUD Sudbury QUE Quebec
WIN Winnipeg THU Thunder Bay REG Regina
FRE Fredericton TOR Toronto WHI Whitehorse
HAL Halifax
Mexico City Listings
Code City Code City Code City
CHH Chihuahua MEX Mexico City HER Hermosillo
DUR Durango GUA Guadalupe
E. Time Zone and Daylight Saving Time Settings
1. Press and hold the "
SET
" button for 1 second.
2. Press and release the "
SET
" button 9 times.
3. The time zone will now flash based on the city selected.
4. Press and release the "+"or "-" button to adjust to the correct time zone.
5. Press and release the "
SET
" button to advance to the Daylight Saving Time setting.
6. "dst ON" will now flash.
7. Press and release the "+" or "-" button to select DST 1 (recognizes Daylight Saving
Time change) or DST 0 (does not change with Daylight Saving Time).
Note
: Some locations (Arizona and parts of Indiana) do not follow Daylight Saving Time.
8. Press and release the "
SET
" button to advance to the weather measurement units
settings (skip steps 1 and 2 in section E if continuing).
F. Weather measurement units (˚F/˚C, inHg/hPa)
1. Press and hold the "
SET
" button for 1 second.
2. Press and release the "
SET
" button 11 times.
3. The selected temperature units will now flash (˚F default/factory setting).
4. Press and release the "+"or "-" button to select ˚F (Fahrenheit) or ˚C (Celsius).
5. Press and release the "
SET
" button to advance to the barometric air pressure units
setting.
6. The selected air pressure units will now flash (inHg default/factory setting).
7. Press and release the "+"or "-" button to select inHg (inches of Mercury) or hPa
(hectopascal or millibars).
8. Press and release the "
SET
" button to advance to the barometric air pressure calibration
setting.
9. The air pressure reading will now flash (29.91 inHg, 1012.8 hPa as default).
10. Press and release the "+"or "-" button to adjust to the correct relative air pressure
based on local reports.
11. Press and release the "
SET
" button to advance to the forecast sensitivity setting.
Note
: Barometric air pressure is usually reported as "relative air pressure". This reading is
based on the combination of absolute air pressure and altitude. In general, an increase in
altitude will result in a decrease in air pressure. Relative air pressure will make readings in
nearby locations relative to each other to allow for proper forecasting. The absolute air
pressure reading in the Weather Center cannot be calibrated, only the relative air pressure.
OK Oklahoma TX Texas (cont.) WV West Virginia
17K Boise City DFW Dallas/Ft. Worth CRW Charleston
LAW Lawton ELP El Paso HLG Wheeling
OKC Oklahoma City HOU Houston WY Wyoming
TUL Tulsa LRD Laredo BYG Buffalo
OR Oregon ODO Odessa CPR Casper
BNO Burns SAT San Antonio CYS Cheyenne
EUG Eugene UT Utah LAA Little America
MFR Medford SAL Saline WYE West Yellowstone
PDX Portland SGU St. George
SLE Salem SLC Salt Lake City
PA Pennsylvania TSN Thompson
CXY Harrisburg VA Virginia
PHL Philadelphia DON Vienna
PIT Pittsburgh LYH Lynchburg
SCR Scranton ORF Norfolk
PR Puerto Rico RIC Richmond
SJU San Juan ROA Roanoke
RI Rhode Island VT Vermont
PVD Providence BTV Burlington
SC South Carolina MPR Montpelier
CHS Charleston WA Washington
CUB Columbia ABE Aberdeen
GMU Greenville ALW Walla Walla
SD South Dakota KTF Kettle Falls
FSD Sioux Falls MVN Mt. Vernon
PIR Pierre OLM Olympia
RAP Rapid City SEA Seattle
TN Tennessee SFF Spokane
BNA Nashville TON Tonasket
CHA Chattanooga YKM Yakima
DKX Knoxville WI Wisconsin
MEM Memphis AUW Wausau
TX Texas GRB Green Bay
ABI Abilene LSE La Crosse
AMA Amarillo MSN Madison
AUS Austin MWC Milwaukee
BRO Brownsville SSQ Spooner