Filter
Top Products
4
RD-T7GN/RD-T5BU(US) / LVT0737-003A / English
English
You can adjust the volume level between MIN (0) and MAX (32)
when the Unit is turned on.
Turn the VOLUME control on the Unit to the right or left to in-
crease or decrease the volume level.
OR
Press the VOLUME + or – button on the Remote Control to increase
or decrease the volume level.
CAUTION: DO NOT turn on the Unit and/or start
playing any source without first setting the
VOLUME control to MIN (0) , as a sudden blast of
sound can damage your hearing.
For private listening
Connect a pair of headphones to the PHONES jack. No sound
comes out of the speakers.
Be sure to turn down the volume before connecting or putting on
headphones.
You can reinforce the bass sound to maintain rich, full bass at low
volume (you can use this effect only for playback):
To get the effect,
press the AHB (Active Hyper Bass) PRO
button.
The “BASS” indicator lights up on the display.
To cancel the effect,
press the button again.
The “BASS” indicator goes out.
You can control the tone by changing the bass and treble.
■
1. Press the BASS/TREBLE button until "BASS"
or "TREBLE" appears on the display.
Each time you press the button, the display changes as follows:
BASS
=
TREBLE
=
original display
=
(back to the beginning)
■
2. Turn the Jog dial on the Unit or press the
VOLUME +/– button on the Remote Control
to adjust the level.
The bass or treble level changes between –6 and +6. (0: Flat)
To exit the tone control mode,
press the BASS/TREBLE but-
ton until the original display appears, or wait for 15 seconds.
To forcibly reset the bass and treble levels to 0 (FLAT),
press the BASS/TREBLE button for 2 seconds or more.
While listening to a CD or the radio, you can see the current time.
To display the clock,
press the CLOCK/DISPLAY button on the
Unit.
To return to the original display,
press the same button until
the original display appears.
Note:
You need to set the clock first in order for it to work. (See
"Setting the Clock" on page 9.)
When operated on AC power ————
You can adjust the brightness of the display's backlighting.
When the Unit is turned on:
Each time you press the SNOOZE/DIMMER button on the Unit or
on the Remote Control, the backlight fully turns on or dims.
When the Unit is turned off(Standby):
Each time you press the SNOOZE/DIMMER button on the Unit or
on the Remote Control, the backlight dims or turns off.
When the Sleep Timer is on:
You can also dims or turn off the backlight with these buttons.
When operated on batteries ————
When the Unit is turned on, you can turn on the backlighting of the
display for a few seconds.
Each time you press the SNOOZE/DIMMER button on the Unit or
on the Remote Control, the backlight turns on for a few seconds.
Power Batteries (6 pcs.):
You can operate the System on batteries. When the batteries are
exhausted, “NO BATT” will appear on the display. In this case, re-
place with the new batteries.
Memory Backup Batteries (3 pcs.):
Your settings such as the preset stations, clock and timer are backed
up with this batteries.
CAUTION:
If memory backup batteries are exhausted or not
installed, and the AC power cord is disconnected
or there is a power failure, the settings you have
made will be erased from memory in approx. half
a day.
Adjusting the Volume
Reinforcing the Bass Sound
(AHB PRO) [RD-T7GN Only]
Tone Control (BASS/TREBLE)
Showing the Time (CLOCK/
DISPLAY)
Adjusting the Brightness
(DIMMER) [RD-T7GN Only]
Using Batteries
RD-T5BU&T7GN(US).book Page 4 Friday, June 29, 2001 9:08 AM