"'-"
<%+,*&%?d^ciZg$EaVcZg8dbWdBVX]^cZ
I]ZejgedhZd[ZY\Z_d^ci^c\^hidegdYjXZV[^c"
^h]ZY![aVi"ZY\ZYhjg[VXZhZZFigures 35 & 36
i]Vi^hhj^iVWaZ[dg_d^cZgndg[^c^h]^c\#>i^hVahdV
cZXZhhVgnhiZe l]ZchfjVg^c\gdj\]dglVgeZY
hidX`#
Figure 36.>aajhigVi^dcd[ZY\Z_d^ci^c\gZhjaih#
To edge joint on the jointer:
1. GZVYVcYjcYZghiVcYSECTION 1: SAFETY,
WZ\^cc^c\dcPage 6#
2. BV`Z hjgZ ndjg hidX` ]Vh WZZc ^cheZXiZY
[dgYVc\ZgdjhXdcY^i^dchVhYZhXg^WZY^ci]Z
Stock Inspection & Requirements^chigjX"
i^dch!WZ\^cc^c\dcPage 24#
3. HZii]ZXjii^c\YZei][dgndjgdeZgVi^dc#LZ
hj\\ZhiWZilZZc
&
¿&+VcY
&
¿-[dgZY\Z_d^ci"
^c\! jh^c\ V bdgZ h]Vaadl YZei] [dg ]VgY
lddYheZX^Zhdg[dgl^YZhidX`#
4. BV`Z hjgZ i]Z [ZcXZ ^h hZi id .%ß! VY_jhi
i]Z WaVYZ \jVgY
(
¿- id
&
¿' VlVn [gdb i]Z
ldg`e^ZXZhZZFigure 35!i]Zci^\]iZci]Z
WaVYZ\jVgYadX``cdW#
5. >[ndjgldg`e^ZXZ^hXjeeZYlVgeZY!eaVXZ
^i hd i]ZXdcXVkZ h^YZ ^h [VXZ Ydlc dc i]Z
hjg[VXZd[i]Z^c[ZZYiVWaZ#
6. HiVgii]Z_d^ciZg#
7. EgZhh i]Z ldg`e^ZXZ V\V^chi i]Z iVWaZ VcY
[ZcXZ l^i] [^gb egZhhjgZ# JhZ ndjg igV^a^c\
]VcYid\j^YZi]Zldg`e^ZXZi]gdj\]i]ZXji!
VcY[ZZYi]Zldg`e^ZXZdkZgi]ZXjiiZg]ZVY#
Note: If your leading hand gets within 4"
of the cutterhead, lift it up and over the
cutterhead, and place it on the portion of
the workpiece that is over the outfeed table.
Now, focus your pressure on the outfeed end
of the workpiece while feeding, and repeat
the same action with your trailing hand when
it gets within 4" of the cutterhead. To keep
your hands safe, DO NOT let them get closer
than 4" from the cutterhead when it is mov-
ing!
8. GZeZViStep 7jci^ai]ZZci^gZZY\Z^h[aVi#
NOTICE
If you are not experienced with a jointer,
set the depth of cut to 0", and practice
feeding the workpiece across the tables as
described below. This procedure will better
prepare you for the actual operation.
Figure 35.:Y\Z_d^ci^c\deZgVi^dc#
Edge Jointing
(
¿-"
&
¿'