Filter
Top Products
user manual
LMS-D6
LMS-D6 user manual
Page 9
OPERATING THE LMS-D6
Preliminary Set-up
The following procedure should be followed when first installing the LMS-D6.
Recall a Factory Preset
To do this press ‘
MENU’,
MENU’, MENU’,
MENU’,
use the
‘BACK’
‘BACK’ ‘BACK’
‘BACK’
or
‘NEXT’
‘NEXT’ ‘NEXT’
‘NEXT’
key to select ‘Xover sub-menu’. Press Press
‘ENTER’
‘ENTER’‘ENTER’
‘ENTER’
; use the
‘BACK’
‘BACK’‘BACK’
‘BACK’
or
‘NEXT’
‘NEXT’‘NEXT’
‘NEXT’
key to select ‘Load a Xover’. Press
‘ENTER’
‘ENTER’‘ENTER’
‘ENTER’
, use the
‘BACK’
‘BACK’‘BACK’
‘BACK’
or
‘NEXT’
‘NEXT’‘NEXT’
‘NEXT’
key to scroll through the preset programs. Press
‘ENTER’
‘ENTER’ ‘ENTER’
‘ENTER’
when the desired program
appears. The crossover will automatically load.
Design your own crossover
To do this press
‘MENU’
‘MENU’‘MENU’
‘MENU’
, use the
‘BACK’
‘BACK’‘BACK’
‘BACK’
or
‘NEXT’
‘NEXT’‘NEXT’
‘NEXT’
key to select ‘Xover sub-menu’. Press
‘ENTER’
‘ENTER’‘ENTER’
‘ENTER’
;
use the
‘BACK’
‘BACK’‘BACK’
‘BACK’
or
‘NEXT’
‘NEXT’‘NEXT’
‘NEXT’
key to select ‘Design a Xover’. Press
‘ENTER’
‘ENTER’‘ENTER’
‘ENTER’
, use the
‘BACK’
‘BACK’‘BACK’
‘BACK’
or
‘NEXT’
‘NEXT’‘NEXT’
‘NEXT’
key to select desired configuration and follow the set-up wizard to design your X-over.
(N.B. When in a menu use the
‘BACK’
‘BACK’‘BACK’
‘BACK’
and
‘NEXT’
‘NEXT’‘NEXT’
‘NEXT’
keys to display menu options. When the
required menu is shown, press
‘ENTER’
‘ENTER’ ‘ENTER’
‘ENTER’
to confirm selection. The current selection will be marked
by a '
∗
' star.)
Use the
‘GAIN’
‘GAIN’ ‘GAIN’
‘GAIN’
key on each channel with the
‘BACK’
‘BACK’‘BACK’
‘BACK’
and
‘NEXT’
‘NEXT’‘NEXT’
‘NEXT’
keys to select HPF, LPF,
parametrics etc. Note: when designing a new crossover the HP and LP filters will be set to their
defaults, see appendix 2.
Note:
Note:Note:
Note: If no action is taken in the menu mode the unit will return to normal 'default' mode. Repeat
above instructions to return to menu mode.
Menu Selections
The following menu selections are available. To access menus, see instructions under preliminary
set-up above.
Xover Sub-Menu
Xover Sub-MenuXover Sub-Menu
Xover Sub-Menu:
Load a Xover:
Loads a pre-defined crossover.
Design a Xover:
Setup wizard for designing a crossover.
Store a Xover:
Stores all output settings as a defined crossover.
Security Sub-Menu
Security Sub-MenuSecurity Sub-Menu
Security Sub-Menu: Locks the unit with a unique user defined 4 digit code. 4 options are available:
changes only, changes + view, changes + mutes, everything. Caution: Do not enter this menu
Caution: Do not enter this menuCaution: Do not enter this menu
Caution: Do not enter this menu
option before reading and understanding the instructions.
option before reading and understanding the instructions.option before reading and understanding the instructions.
option before reading and understanding the instructions.